Council Regulation (EEC) No 3841/86 of 8 December 1986 temporarily suspending the autonomous Common Customs Tariff duties on a number of industrial products

20 . 12 . 86 Official Journal of the European Communities No L 362 / 1
I
(Acts whose publication is obligatory)
COUNCIL REGULATION (EEC) No 3841 / 86
of 8 December 1986
temporarily suspending the autonomous Common Customs Tariff duties on a number of
industrial products
THE COUNCIL OF THE EUROPEAN COMMUNITIES , HAS ADOPTED THIS REGULATION :
Article 1
The autonomous Common Customs Tariff duties for the
products listed in the tables annexed to this Regulation shall
be suspended at the level indicated in respect of each of
them .
These suspensions shall be valid :
— from 1 January to 31 March 1987 for the products listed
in Table I ,
— from 1 January to 30 June 1987 for the products listed in
Table II .
Having regard to the Treaty establishing the European
Economic Community , and in particular Article 28
thereof,
Having Regard to the draft Regulation submitted by the
Commission ,
Whereas production of the products referred to in this
Regulation is at present inadequate or non-existent within
the Community and producers are thus unable to meet the
needs of user industries in the Community ;
Whereas it is in the Community's interest to suspend the
autonomous Common Customs Tariff duties only partially
in certain cases , due particularly to the existence of
Community production , and to suspend them completely in
other cases ;
Whereas , taking account of the difficulties involved in
accurately assessing the development of the economic
situation in the sectors concerned in the near future , these
suspension measures should be taken only temporarily with
their term of validity fixed to coincide with the interests of
Community production ,
Article 2
This Regulation shall enter into force on 1 January 1987 .
This Regulation shall be binding in its entirety and directly applicable in all Member
States .
Done at Brussels , 8 December 1986 .
For the Council
The President
N. LAWSON
Official Journal of the European Communities 20 . 12 . 86No L 362 / 2
ANNEX
TABLE I
Rate of
autonomous
duty (% )
CCT
heading No
Description
ex 38.19 X
ex 39.02 C VI b )
ex 39.02 C XI
ex 81.04 F I
Preparation consisting essentially of alkaline asphalt sulphonate having a density of not less
than 1,2 and not more than 1,5 and a solubility in water of not less than 70 % by weight
Plates , made from a copolymer of maleic anhydrine and styrene , covered on both sides with a
sheet of the abovementioned copolymer modified with a styrene-butadiene block copolymer ,
whether or not pigmented
Polyvinyl alcohol film soluble in water at a temperature of 20 °C
Unwrought hafnium having a purity of not less than 95 % by weight and a zirconium content of
not more than 4,5% by weight
0
0
0
0
20 . 12 .. 86 Official Journal of the European Communities No L 362 / 3
TABLE -II
CCT
heading No
Description
Rate of
autonomous
duty (% )
Mineral oil containing more than 60 % of aromatic constituents by weight and less than 0,8 %
of sulphur by weight , of which not more than 15 % by volume distils at 250 °C , for use in the
manufacture of needle cokes ( a )
Synthetic paraffin wax having a molecular weight of not less than 460 and not more than
1 560
Aluminium hydroxide oxide in the form of pseudo-boehmite
Barium titanate containing by weight not more than 0,05 % of iron
Lanthanum bromide oxide
Hexafluoropropene
Dibromomethane
l,6,7,8,9,14,15,16,17,17,18,18-Dodecachloropentacyclo[12.2.1.1 6 '9 .02 '13 .05 '10]octadeca­
7,15-diene , for use in the manufacture of polyethylene and synthetic rubber (a )
Ethanesulphonyl chloride
1 ,2-Epoxybutane
1 ,2-Epoxy-4-( epoxyethyl )cyclohexane
ex 27.07 G II
ex 27.13 B II
ex 28.20 A
ex 28.47 F
ex 28.52 B
ex 29.02 A I
ex 29.02 A III
ex 29.02 B
ex 29.03 C I
ex 29.09 B
ex 29.09 B
ex 29.09 B
ex 29.14 A XI
ex 29.14 B I
ex 29.14 D IV
ex 29.16 D
ex 29.25 B II c )
ex 29.26 A I
ex 29.31 B
ex 29.35 Q
ex 29.35 Q
ex 29.35 Q
ex 29.35 Q
2,3-Epoxypropan-l-ol (glycidol )
0
0
4
0
0
0
3
0
3
0
0
0
0
0
0
5
0
0
0
4
0
0
0
Trimethyl orthoacetate
2,3-Epoxypropyl methacrylate
Methyl 3-chlorobenzoate
Methyl 5-(2,4-dichlorophenoxy)-2-nitrobenzoate
Barbituric acid
1 ,2-Benzisothiazol-3-one 1,1-dioxide ( saccharin , o-benzoicsulphimide ) and its sodium salt
3,3-Dimethyl-l-methylthiobutanone oxime
Zotepine ( INN)
Ofloxacin ( INN)
3'-Chloro-6'-cyclohexylaminospiro[isobenzofuran-l(3//), 9'-xanthen]-3-one
6'-(A^-Ethyl-/?-toluidino)-2'-(Ar-methylanilino)spiro[isobenzofuran-l(3i/), 9'-xanthen]-3-one
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
No L 362 /4 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 29.35 Q Carteolol hydrochloride ( INNM) 0
ex 29.39 D II Methylprednisolone ( INN) and its salts and esters 1
ex 29.44 C and
ex 30.03 A II b )
Vancomycin ( INN) and its salts and esters
0
ex 32.07 B Inorganic colouring matter preparations mentioned in Note 3 to Chapter 32 , in hollow
polyurethane spheres having a diameter of less than 200 micrometres 0
ex 32.09 A II and
ex 39.01 C V
Polyurethane of 2,2'-(tert-butylimino)diethanol and 4,4'-methylenedicyclohexyl isocyanate ,
dissolved in N , N-dimethylacetamide , with a polymer content of not less than 48% by
weight 0
ex 32.09 A II and
ex 39.02 C XIV a )
Copolymer of p-cresol and divinylbenzene , dissolved in N , N-dimethylacetamide , with a
polymer content of not less than 48 % by weight 0
ex 34.02 Aqueous solution containing not less than 30 % and not more than 50 % of disodium alkyl
[oxydi (benzenesulphonate )] 0
ex 35.07 Aspergillus alkaline proteinase 0
ex 38.16 Unsterile blood serum obtained from the blood of a bovine foetus or non-immunized newly
born calf 0
ex 38.19 E Monoalkylbenzenes , obtained by the alkylation of benzene with polyalkenes and having an
average molecular weight of not less than 680 and not more than 820 0
ex 38.19 G Catalysts , in the form of a powder , consisting of a mixture of titanium , magnesium and
aluminium compounds on a carrier of silicon dioxide , containing by weight :
— not less than 3 % and not more than 6 % of titanium
— not less than 2 % and not more than 3 % of magnesium
— not less than 0,3% and not more than 0,5% of aluminium ,
for use in the production of polyethylene with a density of at least 0,935 g / cm3 (a ) 0
ex 38.19 G Catalysts , consisting of a mixture of titanium , magnesium and aluminium compounds , in the
form of a suspension in hexane , containing by weight :
— not less than 3 % and not more than 6 % titanium
— not less than 1 ,5 % and not more than 3 % magnesium
— not less than 0,3 % and not more than 0,5 % aluminium
for use in the production of polyethylene with aldensity of at least 0,930 g/ cm3 ( a ) 0
ex 38.19 G Catalysts , consisting of dialkyldimethylammonium acetate containing chain lengths of 16 and
18 carbon atoms , suspended in organic solvents to a concentration of not less than 40% by
weight 0
ex 38.19 G Catalysts , in the form of granules or rings having a diameter of not less than 3 mm and not more
than 10 mm, consisting of silver supported on aluminium oxide , the silver content being not less
than 8 % and not more than 20 % by weight 0
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86 Official Journal of the European Communities No L 362 / 5
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 38.19 S Doped silicon wafers , of Czochralski technology , with a diameter of 70 mm or more ,
unpolished and with an oxygen content of not less than 5 x 1017 atoms per cm3 0
ex 38.19 X Aldicarb ( ISO ), dissolved in dichloromethane at a concentration of not less than 35 % and not
more than 40 % by weight 0
ex 39.01 C III a ) Polyester film , dyed in the mass , of a thickness of not more than 25 micrometres and metallized
on one side 6
ex 39.01 C III a ) Polycondensation products of terephthalic acid with a mixture of cyclohex­
1 ,4-ylenedimethanol and ethane-1 ,2-diol in the form of a film 0
ex 39.01 C III a ) Polyester film having a thickness of not more than 70 micrometres , coated on one side with a
substance which becomes coloured when heated to not more than 100 °C in the presence of
salicyclic acid 0
ex 39.01 C III a ) Polyester film having a thickness of not more than 10 micrometres , coated on one side with
salicyclic acid 0
ex 39.01 C III b ) Polycondensation products of terephthalic acid with a mixture of cyclohex­
1 ,4-ylenedimethanol and ethane-i ,2-diol , in one of the forms mentioned in Note 3 (b ) to
Chapter 39 0
ex 39.01 C V Sheets of microporous polyurethane reinforced in the mass with polyamide fibres , having a
thickness of not less than 0,5 mm and not more than 1 ,5 mm, for the manufacture of imitation
leather ( a ) 6,9
ex 39.02 C I a ) Polyethylene , in one of the forms mentioned in Note 3(b ) to Chapter 39 , having a density of not
less than 0,958 g/ cm3 at 23 °C and containing by weight not more than :
— 50 ppm of aluminium
— 2 ppm of calcium
— 2 ppm of chromium
— 2 ppm of iron
— 2 ppm of nickel
— 2 ppm of titanium
— 8 ppm of vanadium
I for the manufacture of chlorosulphonated polyethylene (a ) 0
ex 39.02 C I a ) Polyethylene , in one of the forms mentioned in note 3(b ) to Chapter 39 , having a density of not
less than 0,945 and not more than 0,985 g / cm3 for the manufacture of typewriter ribbon or
similar ribbon ( a ) 0
ex 39.02 C VI a ) An A-B-A block copolymer of polystyrene , ethylene-butylene copolymer and polystyrene ,
containing not more than 35 % by weight of styrene , in one of the forms mentioned in note 3(b )
to Chapter 39 0
ex 39.02 C XI Polyvinyl butyral film having a graduated coloured band 6
ex 39.02 C XIV a) Brominated polystyrene containing not less than 58 % and not more than 71 % by weight of
bromine , in one of the forms mentioned in Note 3(b ) to Chapter 39 0
ex 39.02 C XIV a) Ionomer resin consisting of a salt of a copolymer of ethylene and methacrylic acid 0
ex 39.02 C XIV a) Ionomer resin consisting of a salt of a terpolymer of ethylene , isobutyl acrylate and methacrylic
acid 0
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86No L 362 / 6 Official Journal of the European Communities
CCT
heading No
Description
Rate of
autonomous
duty (% )
ex 39.02 C XIV a )
ex 39.02 C XIV a )
ex 39.02 C XIV a)
ex 39.02 C XIV b )
ex 39.02 C XIV b)
ex 39.02 C XIV b )
ex 39.02 C XIV b)
ex 39.03 B V a ) 2
ex 39.03 B V a ) 2
ex 51.01 A
ex 51.02 A I
ex 56.01 A
Polymerization products of acrylic acid , with alkyl methacrylate and small quantities of other
monomers for use as thickeners in the manufacture of textile printing pastes ( a )
Copolymers of ethylene with acrylic acid , or with methacrylic acid , containing not less than
16 % and not more than 30 % of acrylic acid or methacrylic acid by weight , in one of the forms
mentioned in Note 3(b ) to Chapter 39
Polymerization products of acrylic acid with small quantities of a polyunsaturated monomer ,
for use as a stabilizer in emulsions or dispersions with a pH of more than 13 ( a )
Film of a mixture of polyvinylidene fluoride and of an acrylic polymer having a thickness not
less than 40 micrometres and not more than 60 micrometres
Sheet of a thickness of not less than 1 mm and not more than 3 mm, consisting of a copolymer of
ethylene with chlorotrifluoroethylene , whether or not backed with a woven glass fibre
fabric
Films and sheets of a copolymer of ethylene with chlorotrifluoroethylene with a thickness of not
less than 12 and not more than 400 micrometres
Film of a copolymer of ethylene with methyl acrylate , having a thickness of not more than
0,05 mm, for the manufacture of disposable medical gloves ( a )
Ethylhydroxyethylcellulose , insoluble in water
Hydroxypropylcellulose
Texturized yarn of polypropylene , impregnated with silicone-based water-repellant
Monofil of polytetrafluoroethylene
Acetalized , multicomponent spun fibres with a matrix fibril structure , consisting of emulsion
polymerized polyvinyl alcohol and polyvinyl chloride
Polyvinyl alcohol bonded fibre fabrics , with a thickness of not less than 200 micrometres and
not more than 280 micrometres and of a weight of not less than 20 g /m2 and not more than
50 g/m2 whether or not impregnated or coated , in the piece or cut into rectangles
Needle punched synthetic fibre felts on a woven synthetic fibre base coated or covered on one
side with polytetrafluoroethylene film , for the manufacture of filtration products ( a )
Circular flat lead glass plates , ground and polished with worked edges and having :
— a thickness of not less than 3,5 mm and not more than 5 mm
— a diameter of not less than 135 mm and not more than 140 mm
— a density of not less than 2,88 g/ cm3 , and
— a transmission of not less than 87 % at a wavelength of between 450 nanometres and 800
nanometres for incorporation into video projectors ( a )
Face plates made wholly of glass , having a diagonal dimension of not more than 61 cm and a
raised edge intended for use in the manufacture of monochrome cathode ray tubes (a )
Glass cones with a shaped edge and having a diagonal dimension of not more than 61 cm
intended for use in the manufacture of monochrome cathode ray tubes (a )
0
0
6
0
0
0
6
4
0
0
0
0
0
0
0
0
0
ex 59.03 B
ex 59.17 A
ex 70.07
ex 70.11
ex 70.11
(a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86 Official Journal of the European Communities No L 362 / 7
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 81.04 D I b ) Chromium , in the form of cathode chips , pellets or briquettes , which contains not more than
0,10 % by weight of total oxygen , not more than 0,015 % by weight of total aluminium and not
more than 0,001 % by weight of aluminium compounds insoluble in boiling 5N hydrochloric
acid and in boiling fuming perchloric acid , and evaluated as aluminium , for the production of
alloy for the manufacture of the following parts of gas turbines and jet engines ( a ):
— blades , fixed or movable , including their rings
— vanes
— nozzles 0
ex 84.18 C II b ) Parts of apparatus for catalytic conversion of nitrogen oxides into nitrogen and water ,
consisting of shaped and fired units in honeycomb structure of a mixture of vanadium oxides or
vanadium sulphates and titanium dioxide or barium sulphate , or of vanadium oxide , tungsten
(wolfram) oxide and titanium dioxide , contained in a metal framework 0
ex 84.18 C II b ) Parts of apparatus for catalytic conversion of oxides of nitrogen nitrogen and into water ,
consisting of perforated plates coated with a mixture of oxides of vanadium , titanium and
molybdenum in a metal framework 0
ex 84.53 B Optical reader for reading dot-matrix printing characters and converting them into electrical
signals , comprising a read head containing an optical detector , an amplifier , a focusing lens and
two lamps , linked by one or two flat cables to a central module ofwhich the dimensions do not
exceed 200 x 220 mm, comprising a printed circuit board on which are mounted a
microprocessor , an image recognition circuit and an analog/ digital converter 1
ex 84.55 C Dot- matrix displays , whose external dimensions do not exceed 15 x 90 x 280 mm excluding
cables and connectors consisting of a layer of liquid crystals between two glass sheets or plates
with 30 720 dots (arranged in 64 lines and 480 columns), mounted on a printed-circuit board
comprising electronic components providing drive functions , with or without cable and
connector 0
ex 84.55 C Dot- matrix displays consisting of a layer of liquid crystal between two glass sheets or plates
with a maximum of 15 360 dots ( arranged in 64 lines and 240 columns), complete with an
interface electronics board in C-MOS technology whose exterior dimensions do not exceed
186 x 75 x 15 mm, with not more than 544 connecting areas 0
ex 84.55 C Winchester or thin film technology magnetic heads for disc file peripherals , as well as carrying
arms equipped with such magnetic heads , capable of recording to a density of not less than 10
tracks per millimetre 0
ex 84.55 C Assemblies for automatic data-processing machines , comprising UV-erasable , programmable ,
read-only memories (EPROMs), with a storage capacity of 256 K bits , consisting of a multilayer
substrate , the exterior dimensions of which do not exceed 17 x 39 mm, on which are
mounted :
— two UV-erasable , programmable , read-only memories (EPROMs), in the form of
monolithic integrated circuits , each with a storage capacity of 128 K bits and a quartz
window on the upper surface
— a decoder in the form of a monolithic integrated circuit
— a decoupling capacitor
— two resistances
The assemblies bear :
— an identification marking either consisting of or including the following combination of
figures and letters :
EDH 7832 MM-30
or
— other identification markings relating to assemblies complying with the abovementioned
description 2
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
No L 362 / 8 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
. autonomous
duty (% )
ex 84.55 C
2
Assemblies for automatic data-processing machines , comprising UV-erasable , programmable ,
read-only memories (EPROMs), with a storage capacity of 256 K bits , consisting of a multilayer
substrate , the exterior dimensions of which do not exceed 17 x 39 mm, on which are
mounted :
— four UV-erasable , programmable , read-only memories (EPROMs), in the form of
monolithic integrated circuits , each with a storage capacity of 64 K bits and a quartz
window on the upper surface
— one decoder in the form of a monolithic integrated circuit
— one decoupling capacitor
The assemblies bear :
— an identification marking either consisting of or including the following combination of
figures and letters :
EDH 7832 MC-35
or
— other identification markings relating to assemblies complying with the abovementioned
description
Assemblies for automatic data-processing machines , comprising static random-access
memories of C-MOS technology (C-MOS S-RAMs) with a storage capacity of 32 K bits
consisting of a multilayer substrate , the exterior dimensions of which do not exceed
17 x 39 mm, on which are mounted :
— two static random-access memories of C-MOS technology (C-MOS S-RAMs) in the form
of monolithic integrated circuits each with a storage capacity of 16 K bits
— a decoder in the form of a monolithic integrated circuit
— a decoupling capacitor
The assemblies have not more than 28 connecting pins and bear :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
EDH 8804 C-20
EDH 8804 CL-20
or
— other identification markings relating to assemblies complying with the abovementioned
description
ex 84.55 C
2
ex 84.55 C Assemblies for automatic data-processing machines , comprising static random-access
memories of C-MOS technology (C-MOS S-RAMs) with a storage capacity of 64 K bits
consisting of a multilayer substrate , the exterior dimensions of which do not exceed
17 x 39 mm, on which are mounted :
— four static random-access memories of C-MOS technology (C-MOS S-RAMs) in the form
of monolithic integrated circuits each with a storage capacity of 16 K bits
— a decoder in the form of a monolithic integrated circuit
— a decoupling capacitor
The assemblies have not more than 28 connecting pins and bear :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
EDH 8808 B-20
EDH 8808 C-10
EDH 8808 C-12
EDH 8808 C-15
EDH 8808 C-20
EDH 8808 CL-15
EDH 8808 CL-20
or
2
— other identification markings relating to assemblies complying with the abovementioned
description
20 . 12 . 86 Official Journal of the European Communities No L 362 / 9
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 84.55 C Assemblies for automatic data-processing machines comprising a UV-erasable , programmable ,
read-only memory (EPROM) with a storage capacity of 64 K bits and a static random-access
memory of C-MOS technology (C-MOS S-RAMs) with a storage capacity of 32 K bits
consisting of a multilayer substrate , the exterior dimensions of which do not exceed
17 x 39 mm , with not more than 28 connecting pins , on which are mounted :
— one UV-erasable , programmable , read-only memory (EPROM) in the form of a monolithic
integrated circuit , with a storage capacity of 64 K bits and with a quartz window on the
upper surface
— two static random-access memories of C-MOS technology (C-MOS S-RAMs) in the form
of monolithic integrated circuits , each with a storage capacity of 16 K bits
— one decoder in the form of a monolithic integrated circuit
— one decoupling capacitor
— two resistances
The assemblies bear :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
EDH 90804 BS-25 ( 15 )
EDH 90804 BS-30 (20 )
or
— other identification markings relating to assemblies complying with the abovementioned
description 2
ex 84.55 C Assemblies for automatic data-processing machines , consisting of two stacked substrate layers
with one or two static random access memories of bipolar technology (bipolar S-RAMs) in the
form of monolithic integrated circuits , each with a storage capacity of 1 K bits and with a
maximum storage capacity of 4 K bits , contained in a housing the exterior dimensions ofwhich
do not exceed 13x13 mm , with not more than 23 connecting pins and bearing :
— an identification marking , either consisting of or including one of the following
combinations of figures :
770965
4599497
7379442
or
— other identification markings relating to assemblies complying with the abovementioned
description 0
ex 84.55 C Assemblies for automatic data processing machines comprising a 32-bit microprocessor of
C-MOS technology in the form of an assembly , consisting of a central processing unit (CPU )
and a memory unit contained in two separate chips mounted on a substrate the exterior
dimensions of which do not exceed 16 x 55 mm, with not more than 60 connecting pins and
bearing :
— an identification marking consisting of, or including the following combinations :
57-1940057-00000
or
0— other identification markings for devices relating to the abovementioned description
ex 84.55 C Magnetic bubble memories with a storage capacity of not more than four megabits contained in
a housing the exterior dimensions of which do not exceed 43 x 44 mm, with not more than
42 connecting pins or contact areas and bearing:
No L 362 / 10 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 84.55 C
(cont'd)
— an identification marking consisting of or including one of the following combinations of
figures or figures and letters :
BDL 0133 MBM 2011 FBM 64 DA
BDL 0134 MBM 2256 7110
BDN 0151 FBM 54 DB 7114-1
or
— other identification markings relating to magnetic bubble complying with the
abovementioned description 0
ex 84.55 C Component forming the arithmetic / logic element of a central processing unit , comprising not
more than nine printed circuit boards , the dimensions of which do not exceed 290 x 310 mm
on each of which are mounted not more than 121 ECL gate arrays or ECL random access
memories (ECL-RAMs ) and combinations thereof contained in a framework the dimensions of
which do not exceed 611 x 501 x 596 mm which serves as a housing and interconnector for
the printed circuit boards , which bear :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
CO1B 2675 E 500
CO1B 2675 H 500
CO1B 2675 H 501
CO1B 2675 H 502
CO1B 2675 H 503
CO1B 2675 H 504
or
— other identification markings relating to components complying with the abovementioned
description 0
ex 84.55 C Display unit with maximum dimensions , excluding cables and connectors , ofl5 x 115 x 290
mm, comprising two layers or sheets of glass enclosing 128 000 liquid-crystal dots arranged in
200 rows and 640 columns , fixed to a printed circuit fitted with electronic components
performing control functions , with or without cables and connectors 0
ex 84.55 C Integrated memory unit for electronic typewriters , comprising a printed circuit with two or four
static read-write random-access memories each with 8 K x 8 bit capacity , electronic control
components and memory back-up batteries , contained in a cartridge fitted with connectors, of
external dimensions not exceeding 11 X 40 x 90 mm, and bearing an identification mark
consisting of or including the following combination of letters and figures :
MEMOCART
i
or
other identification markings relating to integrated memory units complying with the
abovementioned description 0
ex 84.59 B Integrally forged , rough-turned components , with unit weights of more than 150 tonnes , for
reactor pressure vessels 0
ex 84.61 B Hydraulic five-stage valve , with two magnetic valves for servo-control , consisting essentially of
three plastic sections , for incorporation in water softening devices with automatic regeneration
( throughflow and counterflow) with a maximum capacity of 650 L ion exchange volume ( a ) 0
ex 84.63 B II Integrally forged and roughly shaped generator and turbine shafts of a weight exceeding
215 tonnes 0
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions
20 . 12 . 86 Official Journal of the European Communities No L 362 / 11
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.01 B I b ) DC electric motor , brushless , with a maximum torque of 0,20 N/m, with an incorporated
electronic control plate , outside rotor with circular cross-section and maximum diameter of
95 mm, aluminium precision-made hub with inside diameter of 28,6 mm, speed of 300 or 360
rpm , supply voltage of 12 volts ± 10 % 0
ex 85.01 B I b ) DC electric motor , brushless , with a maximum torque of 0,20 N /m , with outside rotor of a
maximum diameter of 55 mm, coupling flange of a diameter of 77 mm and precision-made
chuck of a diameter of 44 mm, four-phase winding , rated speed of 3 600 rpm , supply voltage
12 volts ± 10 % and fitted with wires and connectors 0
ex 85.01 B I b ) Two or three-phase DC electric motor , brushless , with a maximum torque of 0,20 N/m , with
an external rotor of 62 mm maximum diameter and incorporating an electronic control panel ,
maximum dimensions 85 x 85 x 20 mm, including the shaft , nominal operating voltage of
12 volts ± 10 % and a rate of rotation of 300 rpm 0
ex 85.01 B I b ) Bipolar stepping motors with an angle of step of 1 ,8 degrees , 200 steps per revolution , 2-phase
rotation sequence with bipolar-type windings , maximum external dimensions of
39 x 39 x 20 or 25 mm excluding shaft , fixing screws and boss , with a minimum torque of
0,25 N/m for the version with a maximum height of 20 mm and 0,35 N/m for the version with
a maximum height of 25 mm 0
ex 85.01 B I b )
J
Hybrid steppingmotor , with an angle of step of 0,9° , 400 steps per revolution , 4-phase rotation
sequence with bipolar-type winding , consisting of a rotor , of a laminated stator held between
two square flanges , not more than 40 mm wide , fitted with biterminate shaft , wires and
connectors 0
ex 85.01 B I b ) Hybrid stepping motor with an angle of step of 0,9° , 400 steps per revolution , 2-phase rotation
sequence and bipolar windings , comprising a rotor and a stator encapsulated in a cylindrical
housing with a maximum diameter of 47 mm and maximum thickness of 14 mm, fitted with a
single shaft output and cables with connectors 0
ex 85.01 Bib) Hybrid stepping motor with an angle of step of 0,9° , 400 steps per revolution and 2-phase
rotation sequence , and bipolar windings , comprising a rotor , a laminated stator enclosed
between two square section flanges with sides not exceeding 40 mm, an integral two or
three-phase tachometer enclosed in a cap with a maximum diameter of 35 mm, and separate
cables and connectors for the motor and tachometer outputs , with maximum dimensions of
40 x 40 x 62 mm, including the shaft 0
ex 85.01 B I b ) Direct-current bipolar stepping motor with a single stator , an output of not more than 37,5 W,
a rotary angle / step of 1 80° , two steps per rotation , a two-phase rotation cycle with single-pole
winding , an output torque of not less than 0,1 x 10"6 Nm and not more than 0,1 X 10"4 Nm
and a supply voltage of not more than 3 V 0
ex 85.01 B I b ) Hybrid stepping motor with an angle of step of 0,9° , 400 steps per revolution , two-phase
rotation sequence with bipolar winding , comprising a rotor , a laminated stator enclosed
between two flanges , one of square section with a side of 40 mm maximum, the other front face
having a shaped profile with two projections with fixing slots , aan integral two- or three-phase
tachometer enclosed in a cover of diameter of 35 mm maximum, separate cables and connectors
for the motor and tachometer outputs , with overall dimensions not exceeding 40 x 40 x 62
mm, including the shaft but excluding the projections of the front flange
1
J
0
ex 85.01 B II Static converter consisting of a combination of seven diodes in cascade , for output voltages of
not less than 40 kV DC with a load current of not less than 3 mA 0
No L 362 / 12 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.03 Dry zinc / carbon batteries of a voltage of not less than 5,5 and not more than 6,5 and of a size
not exceeding 110 x 90 x 5 mm, for incorporation in film cassettes for instant pictures (a ) 0
ex 85.03 Lithium iodine single cell battery with dimensions of 45 x 9 X 23 mm and a voltage not
exeeding 2,8 0
ex 85.13 B or
ex 85.21 D II
Opto-electronic receiving device (PINFET receiver ) with a wavelength range 1 300 - 1 600
nanometres , and a speed of not less than 678 megabits per second , in the form of a hybrid
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
25 mm x 13 mm x 13 mm , with not more than 16 connecting pins , with an attached optical
fibre lead (pig-tail ), and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
416 / 7 / 97013
QDFI-XXXX-001
or
— other identification markings relating to devices complying with the abovementioned
description 0
ex 85.18 B Adjustable capacitor , in the form of a circular plate with a diameter of not more than 3 mm,
fitted with a screw head in its centre and two connecting tags , of a thickness not exceeding 3 mm
and a capacity of from 5 to 30 picofarads , for the manufacture of products falling within
Chapter 91 ( a ) 0
ex 85.19 A Thermal relays contained in a hermetically sealed glass cartridge not exceeding 35 mm in length
excluding wires , with a maximum leakage rate of 10-6 cm3 He / sec at one bar in the temperature
range 0 to 160 °C , to be incorporated into compressors for refrigerating equipment ( a ) 0
ex 85.19 A Reed switches in the form of a glass capsule containing not more than three electrical contacts
on metal arms and a small quantity of mercury 0
ex 85.19 C Single-face printed circuit , of dimensions not exceeding 30 x 30 mm, for the manufacture of
products falling within Chapter 91 ( a ) 0
ex 85.21 A V Cathode-ray tubes with dot mask ( so-called dot-mask technology), with electron guns arranged
in triangular fashion (so-called delta technology ), with a distance between the coloured dots of
0,31 mm, with devices for automatic convergence 0
ex 85.21 A V Cathode-ray tubes with a memory (direct view storage tubes ) for the reproduction of
alphanumeric and analogue data , equipped with a scanning device , for reading the images 0
ex 85.21 A V Colour cathode ray tubes with a dot mask equipped with electron guns placed side by side
( in-line technology ) with a distance of less than 0,45 mm between colour dots and with at least
one of the following characteristics :
— a diagonal screen measurement of not less than 42 cm or less than 26 cm , a diagonal angle of
deflection of not more than 90 degrees and convergence errors exceeding 0,8 mm at the
corners ,
— a built in-system , inseparably linked to the tube , for the absorption of vibrations ( so called
potting system),
— without internal magnetic screen ,
— a phosphor layer calibrated with the following nominal coordinates for the colour dots :
red green blue
X
Y
0,64
0,33
0,29
0,60
0,15
0,06
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86 Official Journal of the European Communities No L 362 / 13
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 A V
(cont'd)
or
X
Y
0,64
0,34
0,31
0,595
0,155
0,07
or
X
Y
0,62
0,33
0,21
0,615
0,15
0,06
or
X
Y
0,610
0,350
0,307
0,595
0,150
0,065
or
X
Y
0,61
0,35
0,205
0,680
0,15
0,065
or
X
Y
0,62
0,35
0,29
0,60
0,15
0,065 0
ex 85.21 A V Colour cathode ray tubes with a dot mask equipped with electron guns in a triangular fashion
(delta technology ) with a distance of less than 0,4 mm between colour dots , with at least one of
the following characteristics :
— a diagonal screen measurement of at least 66 cm
— equipped with a phosphor layer calibrated with the following nominal coordinates for the
colour dots :
red green blue
X
Y
0,64
0,33
0,29
0,60
0,15
0,06
or
X
Y
0,64
0,34
0,31
0,595
0,155
0,07
or
X
Y
0,610
0,350
0,307
0,595
0,150
0,065
or
X
Y
0,61
0,35
0,205
0,680
0,15
0,065
or
0,15
0,065
X
Y
0,62
0,35
0,29
0,60 0
ex 85.21 A V Displays in the form of a tube consisting of a glass housing mounted on a board the dimensions
ofwhich do not exceed 350 x 300 mm excluding leads . The tube contains one or more rows of
characters or lines arranged in rows , each character or line consisting of fluorescent or
phosphorescent elements . These elements are mounted on a metallized base which is covered
with fluorescent substances or phosphorescent salts which give off light when bombarded with
electrons 0
ex 85.2.1 A V Flat screen monochrome cathode ray tubes having a diagonal screen measurement of not less
than 142 mm and not more than 145 mm , a luminescence of between 300 and 400 lumen , a
resolution of between 0,06 and 0,1 mm, phosphor types P 1 or P 55 or P 56 , an anode voltage
of more than 34 kV , a focus voltage of more than 7 kV and a cathode current of not less
than 3 mA 0
ex 85.21 C Quartz crystal oscillating at a frequency of 32 768 Hz , contained in a cylindrical housing of a
length not exceeding 8,2 mm and a diameter not exceeding 3,2 mm, for the manufacture of
products falling within Chapter 91 ( a ) 0
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
No L 362 / 14 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Digital displays of a size not exceeding 25 x 35 mm , consisting of a printed circuit board on
which are mounted , under a plastic cover , up to 22 light-emitting diodes manufactured from
gallium-based semi-conductor compounds . Each display consists of a single character with or
without a plus or minus sign and / or one or two dots 7
ex 85.21 D II Digital displays , consisting of a printed circuit board of a size not exceeding 35 x 90 mmwith a
single line of characters , not less than three in number , comprising light-emitting diodes made
from gallium-based semi-conductor compounds mounted thereon . Each character is composed
of up to eight segments with or without a decimal point and the line of characters has a
protective cover of plastic 0
ex 85.21 D II Germanium-gold diodes with forward voltage not exceeding IV at 5mA 0
ex 85.21 D II Light-emitting diode (LED ) made from a gallium-based semiconductor compound contained in
a housing the exterior dimensions of which do not exceed 20 x 21 mm, with two connecting
pins and bearing :
— an identification marking consisting of or including one of the following identification
markings :
LT 9305 LT 9306
SLF 209 SLF 909
or
— other identification markings relating to LEDs , complying with the abovementioned
description 0
ex 85.21 D II Read-only memories (ROMs), in the form of a monolithic integrated circuit , with a storage
capacity of 16 K x 8 bits , with read-register and serial output control , contained in a housing
the exterior dimensions ofwhich do not exceed 50x16 mm, with not more than 40 connecting
pins and bearing :
— an identification marking either consisting of one of the following combinations of figures
or including one of those combinations :
from 62000 to 62999
or
— other identification markings relating to ROMs complying with the abovementioned
description 0
ex 85.21 D II Read-only memory in C-MOS technology (C-MOS ROM) with a storage capacity of 256 K bits
and a standby current of not more than 0,03 mA , in the form of a monolithic integrated circuit
contained in a housing the exterior dimensions of which do not exceed 17 x 50 mm, with not
more than 54 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
HN 61256
HN 613256
MB 83256
or
— other identification markings relating to C-MOS ROMs complying with the
abovementioned description 7
ex 85.21 D II Read-only memory of C-MOS technology (C-MOS ROM) with a storage capacity of one
megabit in the form of a monolithic integrated circuit contained in a housing the exterior
dimensions of which do not exceed 17x39 mm, with not more than 28 connecting pins and
bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
20 . 12 . 86 Official Journal of the European Communities No L 362 / 15
CCT
heading No
Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
HN 62301 P
MB 831000
MB 831124
TC 531000 P
or
— other identification markings relating to C-MOS ROMs complying with the
abovementioned description 7
ex 85.21 D II Programmable , non-erasable , read-only memories (PROMs) of Schottky TTL technology ,
with a storage capacity of 2 K bits , in the form of a monolithic integrated circuit , contained in a
housing the exterior dimensions of which do not exceed 17 x 39 mm, with not more than
24 connecting pins or contact areas , and bearing:
— an identification marking either consisting of one of the following combinations of figures
or figures and letters or including one of those combinations :
76 LS 0327 S 12
27 S 13
28 L 22
28 LA 22
28 L2 XMFC
5305
5306
5308
5309
53 S 240
53 S 241
54 S 570
54 S 571
5604
5624
7620
7621
82 S 114
82 S 130
82 S 131
93436
93446
6305
6306
6308
6309
63 S 240
63 S 241
6335
6336
7053
7058
74 S 570
74 S 571
29613
29770
29771
38510 MB 7115
MB 7116
MB 7117
MB 7118
or
— other identification markings relating to PROMs complying with the abovementioned
description 0
ex 85.21 D II Programmable , non-erasable , read-only memories (PROMs) with a storage capacity of 4 K bits ,
in the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 17 x 39 mm, with not more than 24 connecting pins or 28 contact areas
and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures or figures and letters :
CY 7 C 22518 S 42 29620 54 S 472 74 S 472
18 S 46 29621 54 S 473 74 S 473
18 SA 42 29622 54 S 474 74 S 474
18 SA 46 29623 54 S 475 74 S 475
29624 54 S 476 74 S 476
24 S 41 29625 54 S 477 74 S 477
24 SA 41 29626 54 S 572 74 S 572
29627 54 S 573 74 S 573
27 S 15 54740
27 S 25 3604 54741 7640
27 S 26 3624 7641
27 S 27 3625 5605 7642
27 S 28 5625 7643
27 S 29 38510 7644
27 S 30 6340 7645
27 S 31 5340 6341 7646
27 S 32 5341 63 S 440 7647
27 S 33 53 S 440 63 RA 441 7648
53 RA 441 63 RS 441 7649
28 L 42 53 RS 441 63 S 441
No L 362 / 16 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
28 L 45 53 S 441 6348 82 HS 137
28 L 46 5348 6349 82 HS 147
28 P 42 5349 6350 82 S 115
28 P 45 5350 6351 82 S 136
28 R 45 5351 6352 82 S 137
28 S 4 XFD 53522 6353 82 S 140
28 SA 41 5353 82 S 141
28 S 42 HM 6641 82 S 142
28 SA 42 82 S 146
28 S 45 7054 82 S 147
28 S 46 7059
28 SA 46 l 93438
7121 93448
7122 93452
7123 93453
7124
7125
7126
7226
or
— other identification markings relating to PROMs complying with the abovementioned
description 0
ex 85.21 D II Programmable , non-erasable read-only memories (PROMs) with a storage capacity of 8 K bits ,
in the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 17 x 39 mm, with not more than 24 connecting pins or 28 contact points
and bearing :
— an identification marking either consisting of one of the following combinations of figures
and letters or including one of those combinations :
24 S 81 3628 74 LS 478 82707 CY 7 C 235
24 SA 81 74 S 2708 82708 CY 7 C 281
24 S 86 5380 74 S 454 82 HS 185 CY 7 C 282
5381 74 S 455 82 LS 180
27 S 180 5388 74 S 478 82 LS 181
27 S 181 5389 74 S 479 82 S 180
27 S 185 53 S 840 82 S 181
27 S 35 53 S 841 7608 82 S 182
7680 82 S 183
28 L 85 54 LS 478 7681 82 S 184
28 L 86 54 S 2708 7684 82 S 185
28 P 85 54 S 454 7685 82 S 2708
28 R 35 54 S 455 7686
28 R 85 54 S 478 7687 87 S 180
28 S 2708 54 S 479 7688 87 S 181
28 S 85 7689 87 S 184
28 S 86 6380 87 S 185
28 SA 86 6381 77 S 180 87 S 186
28 S 8 XMFE 6388 77 S 181 87 S 187
6389 77 S 184
29623 63 S 840 77 S 185 93450
29630 63 S 841 77 S 186 93451
29631 77 S 187 93460
29632 7050 93461
29633 7055 TBPS 81 M 93465
29634 7060 93466
29635 93 L 450
29636 7127 93 L 451
29637 7128
29650 7129 9460
29651 7130
29652 7131
29653 7132
7232
20 . 12 . 86 Official Journal of the European Communities No L 362 / 17
CCT
heading No Description
Rate of
autonomous
duty (% )
orex 85.21 D II
(cont 'd) — other identification markings relating to PROMs complying with the abovementioned
description 0
ex 85.21 D II UV-erasable , programmable , read-only memories (EPROMs) with a storage capacity of 2 K
bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 17 x 39 mm, with a quartz window on the upper surface
and bearing:
— an identification marking either consisting of one of the following combinations of figures
or including one of the following combinations :
AMI 702 ADC
82140 PP
or
— other identification markings relating to EPROMs complying with the abovementioned
description 4
ex 85.21 D II UV-erasable , programmable , read-only memory (EPROM) equipped with a programmable
input / output system , with a storage capacity of 2 K x 8 bits , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
17 x 52 mm , with a quartz window on the upper face and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
D 8755 A
TMP 8755 AC
or
— other identification markings relating to memories complying with the abovementioned
description 0
ex 85.21 D II Electrically erasable programmable , read-only memories (E2PROMs ) with a storage capacity
of 4 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 17 x 33 mm, with not more than 24 connecting pins and
bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
X 2804 A X 2404 X 24 C 04
or
— other identification markings relating to E2PROMs complying with the abovementioned
description 0
ex 85.21 D II Electrically erasable , programmable , read-only memories (E2PROMs ) with a storage capacity
of 16 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 17 x 39 mm , with not more than 32 connecting pins or
contact areas and bearing :
— an identification marking consisting of or including one of the following combination of
figures and letters :
AM 2817 A
X 24 C 16
X 2816 A
52 B 13
52 B 13 H
or
— other identification markings relating to E2PROMs complying with the abovementioned
description 0
No L 362 / 18 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Electrically erasable , programmable , read-only memories (E2PROMs) with a storage capacity
of 64 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 17 x 39 mm, with not more than 32 connecting pins or
contact areas and bearing :
— an identification marking consisting of or including one of the following combination of
figures and letters :
MBM 28 C 64
MBM 28 C 65
X 2864 A
MCM 2864
52 B 33
52 B 33 H
or
— other identification markings relating to E2PROMs complying with the abovementioned
description 0
ex 85.21 D II Electrically erasable , programmable , read-only memories (E2PROMs) with a storage capacity
of 128 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 17 X 39 mm, with not more than 32 connecting pins or
contact areas and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
X 28128 A
or
— other identification markings relating to E2PROMs complying with the abovementioned
description 0
ex 85.21 D II Electrically erasable , programmable , read-only memories (E2PROMs) with a storage capacity
of 256 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 17 X 39 mm , with not more than 32 connecting pins or
contact areas and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
28256
28 C 256
48 C 256
or
— other identification markings relating to E2PROMs complying with the abovementioned
description 0
85.21 D II Static , random-access memories of TTL technology (TTL S-RAMs) with a storage capacity of
1 K bit and an access time not exceeding 45 ns , in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 16x30 mm , with not
more than 22 connecting pins and bearing:
— an identification marking either consisting of or including one of the following
combinations of figures
93422
93425
or
— other identification markings relating to TTL S-RAMs complying with the abovementioned
description 0
20 . 12 . 86 Official Journal of the European Communities No L 362 / 19
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Static , random-access memories of N-MOS ( including H-MOS ) technology (N-MOS S-RAMs )
with a storage capacity of 1 K x 4 bits and access time not exceeding 70 ns , in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 8 x 23 mm, with not more than 18 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
AM 2149
PD 2149
SY 2149 H
TMS 2149
or
— other identification markings relating to N-MOS S-RAMs complying with the
abovementioned description 7
ex 85.21 D II Static , random-access memories of C-MOS technology (C-MOS S-RAMs), with a storage
capacity of 4 K x 1 bit , a maximum access time not exceeding 70 ns and a standby mode supply
current of less than 1 mA , in the form of a monolithic integrated circuit , contained in a housing
the dimensions of which do not exceed 9 x 26 mm , with 18 connecting pins , and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
6147
MCM 61 L 47
or
— other identification markings relating to C-MOS S-RAMs complying with the
abovementioned description 0
ex 85.21 D II Static , random-access memory of C-MOS technology (C-MOS S-RAM) with a storage capacity
of 2 K x 8 bits and with a maximum standby power of 0,005 milliwatts at 25 °C in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 17 x 33 mm with not more than 24 connecting pins and bearing :
— an identification marking consisting of or including one of the following combination of
figures and letters :
TC 5516 A
or
— other identification markings relating to C-MOS S-RAMs complying with the
abovementioned description 7
ex 85.21 D II Static , random-access memories of N-MOS ( including H-MOS ) technology (N-MOS S-RAMs )
with a storage capacity of 8 K bits , in the form of a monolithic integrated circuit , contained in a
housing the exterior dimensions of which do not exceed 17hx 39 mm , with not more than
24 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures or figures and letters :
8104
8108
8112
8114
8185
4008
4118
PD 421
4801
or
— other identification relating to N-MOS S-RAMs complying with the abovementioned
description 0
No L 362 / 20 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Static , random-access memories of N-MOS ( including H-MOS ) technology (N-MOS S-RAMs )
with a storage capacity of 256 x 4 bits with access time not exceeding 25 nano seconds in the
form of a monolithic integrated circuit , contained in a housing the exterior dimensions of which
do not exceed 17 x 39 mm , with not more than 24 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures or figures and letters :
9122 - 25
91 L 22 - 25
or
— other identification markings relating to C-MOS S-RAMs complying with the
abovementioned description 0
ex 85.21 D II Static , random-access memories of C-MOS technology ( C-MOS S-RAMs ) with a storage
capacity of 64 K bits in the form of a monolithic integrated circuit , contained in a housing the
exterior dimensions of which do not exceed 18 x 39 mm , with not more than 32 connecting
pins or contact areas and bearing :
— an identification marking consisting of the following combination of figures and letters or
including one of those combinations :
TC 5564
TC 5565 C
HM 6264 P
HM 6264 LP
MB 8464
MCM 6164
HM 6264 LFP
MB 81 C 71
MB 81 C 78
or
— other identification markings relating to C-MOS S-RAMs complying with the
abovementioned description 0
ex 85.21 D II Static , read / write , random-access memories of N-MOS ( including H-MOS ) technology
(N /H-MOS RAMs , static ) with a storage capacity of 72 K bits , in the form of a monolithic
integrated circuit , contained in a housing whose dimensions do not exceed 10 x 39 mm , with
not more than 28 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
TMM 2089
or
— other identification markings relating to static , read /write memories complying with the
abovementioned description 0
ex 85.21 D II Monolithic integrated circuit consisting of a static , random-access memory (S-RAM) with a
storage capacity of 2 K bits , superimposed bit-for-bit on an electrically erasable ,
programmable , read-only memory (E 2PROM), contained in a housing the exterior dimensions
of which do not exceed 17 x 39 mm , with not more than 28 connecting pins and bearing :
— an identification marking consisting of the following combinations of figures and
letters :
X 2002
or
— other identification markings relating to S-RAMs stacked on E2PROMs complying with the
abovementioned description 0
20 . 12 . 86 Official Journal of the European Communities No L 362 / 21
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Monolithic integrated circuit consisting of a static , random-access memory ( S-RAM ) with
a storage capacity of 4 K bits , superimposed bit-for-bit on an electrically erasable ,
programmable , read-only memory (E 2PROM), contained in a housing the exterior dimensions
of which do not exceed 17 x 39 mm , with not more than 28 connecting pins and bearing :
— an identification marking consisting of the following combination of figures and letters :
X 2004
or
— other identification mmarkings relating to SRAMs stacked on E 2PROMs complying with the
abovementioned description 0
ex 85.21 D II Random access memories of ECL technology (ECL-RAMs) with a storage capacity of 4 K bits
and an access time not exceeding 50 ns in the form of a monolithic integrated circuit , contained
in a housing whose exterior dimensions do not exceed 11 x 32 mm, with not more than 24
connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures :
10470
10474
or
— other identification markings relating to ECL-RAMs complying with the abovementioned
description 0
ex 85.21 D II Field programmable array logics ( PALs ) of bipolar technology , in the form of a monolithic
integrated circuit , with fusible links , a programmable AND array , fixed OR array , not more
than 20 inputs and not more than 10 outputs , whether or not with registers , contained in a
housing the exterior dimensions of which do not exceed 19 x 39 mm , with not more than 28
connecting pins and bearing :
— an identification marking either consisting of or including the following combinations of
figures and letters :
10 H 8 16 A 4 18 L 4
10 L 8 16 C 1
16 H 2 20 C 1
12 H 6 16 L 2 20 L 2
12 L 6 16 L 6 20 L 10
20 R 4
12 L 10 16 L 8 20 X 4
16 R 4 20 X 8
14 H 4 16 R 6 20 X 10
14 L 4 16 R 8
14 L 8 16 X 4
or
— other identification markings relating to PALs complying with the abovementioned
description 5
ex 85.21 D II Programmable , non-erasable , logic circuits ( field programmable logic array ) of TTL Schottky
technology , with not more than 48 AND functions , not more than eight OR functions , and not
more than 16 inputs , in the form of a monolithic integrated circuit , contained in a housing the
exterior dimensions of which do not exceed 17 x 39 mm , with not more than 28 connecting
pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures or figures and letters :
No L 362 / 22 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
FP 54 AS 839
FP 54 AS 840
SN 54 LS 333
SN 54 LS 334
SN 54 LS 335
SN 54 LS 336
82 S 100
82 S 101
93458
93459
FP 74 AS 839
FP 74 AS 840
SN 74 LS 333
SN 74 LS 334
SN 74 LS 335
SN 74 LS 336
or
— other identification markings relating to field programmable logic arrays complying with
the abovementioned description 5
ex 85.21 D II Semi-custom logic array (Gate arrays ) of C-MOS technology , in the form of a monolithic
integrated circuit , with not less than eight thousand 2-input NAND functions , contained in a
housing the exterior dimensions of which do not exceed 39 x 39 mm, with not less than 179
connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
MB 66000 VH
or
— other identification markings relating to C-MOS logic arrays complying with the
abovementioned description 0
ex 85.21 D II Video gate arrays programmed to control graphics and memory , in the form of a monolithic
integrated circuit contained in a housing whose exterior dimensions do not exceed 15 x 52
mm , with not more than 40 connecting pins and bearing :
— an identification marking consisting of or including t;he following combination of
figures :
38300
o.r
— other identification markings relating to programmed gate arrays complying with the
abovementioned description „ 0
ex 85.21 D II Single-chip microcomputers , in the form of a monolithic integrated circuit , consisting of an
arithmetical unit with a capacity of four bits plus a read-only memory (ROM) with a capacity of
not less than 1 8 K bits and not more than 65 K bits and a random-access memory (RAM) with a
capacity of not less than 512 bits and not more than 4 K bits , contained in a housing the exterior
dimensions of which do not exceed 17 x 58 mm, with not more than 80 connecting pins and
bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
CD 3200-3299 TP 0310-03299 HD 38800
TP 0450-04599 HD 38820
TMC 0270-0279 TP 0480-04899 HD 44796
TMC 0500-0599 TP 0500-05999 HD 44800
TMC 0980-0989 HD 44801
TMC 1500-1599 HD 44820
TMC 1980-1999 HD 44840
HD 44860
HD 614042
or
— other identification markings relating to single-chip microcomputers complying with the
abovementioned description 0
ex 85.21 D II Central processing unit of N-MOS ( including H-MOS ) technology (N-MOS CPU), in the form
of a monolithic integrated circuit consisting of a 16 x 16 bit service memory , a 16 x 20 bit
service memory , a 32 x 32 bit service memory , an 8 x 8 bit service memory , a 16 bit register ,
two 20 bit registers , an 8 bit register , one 12 bit register , a 5 bit counter and timing network ,
contained in a housing the exterior dimensions of which do not exceed 25 x 25 mm, with not
more than 68 connecting pins and bearing :
20 . 12 . 86 No L 362 / 23Official Journal of the European Communities
CCT
heading No . Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont 'd)
— an identification marking either consisting of or including the following combination of
figures and letters :
LSI-604041855
or
— other identification markings relating to N-MOS central processing units complying with
the abovementioned description
ex 85.21 D II Contention resolving local area network (LAN) controllers , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
63 x 16 mm , with not more than 48 connecting pins , and bearing:
— an identification marking either consisting of the following combinations of figures or
figures and letters or including one of those combinations :
MCM 68590
AM 7990
COM 9026
WD 2840
8001
8003
82586
82588
or
— other identification markings relating to contention resolving local area network controllers
complying with the abovementioned description
ex 85.21 D II Hard-disc controllers of N-MOS ( including H-MOS ) technology (N-MOS HDCs), in the form
of a monolithic integrated circuit , contained in a housing the exterior dimensions of which do
not exceed 15 x 53 mm , with not more than 40 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
0
0
0
0
HDC 9224
PD 7261
WD 1010
WD 2010
WD 5010
or
— other identification markings relating to N-MOS HDCs complying with the
abovementioned description
ex 85.21 D II Arithmetic-logic units of N-MOS ( including H-MOS ) technology , in the form of a monolithic
integrated circuit , consisting of one 32 bit register , one 24 bit register , one 4 bit register , twelve
1 bit registers , two 1 6 x 24 bit service memories , one logic network performing arithmetic and
logic operations , decodifying logic , an error detection and management logic , one 8 bit counter
and a timing network , contained in a housing the exterior dimensions of which do not exceed
23 x 82 mm , with not more than 64 connecting pins and bearing:
— the identification marking :
ALU 0486
or
— other identification markings relating to arithmetic-logic units complying with the
abovementioned description
ex 85.21 D II Logic control circuits of N-MOS ( including H-MOS) technology , in the form of a monolithic
integrated circuit , consisting of one 7 bit register , three timers , one multiplexer sequential and
combining networks intended to perform control operations , decodifying logic , error detection
and management logic and a timing network , contained in a housing the exterior dimensions of
which do not exceed 23 x 82 mm , with not more than 64 connecting pins and bearing :
No L 362 / 24 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty ( % )
ex 85.21 D II
(cont 'd)
— the identification marking :
MIC 0482
or
other identification markings relating to logic control circuits complying with the
abovementioned description
ex 85.21 D II Logic circuit of N-MOS ( including H-MOS ) technology (N-MOS LC ) serving as a clock
generator for central process unit , main memory and input / output interfaces , in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 25 x 25 mm , with not more than 68 connecting pins and bearing :
an identification marking either consisting of or including the following combination of
figures and letters :
H 108982 (MCC)
or
— other identification markings relating to N-MOS logic circuits (N-MOS LCs ) complying
with the abovementioned description
ex 85.21 D II Sequence control circuits of N-MOS ( including H-MOS ) technology , in the form of a
monolithic integrated circuit , consisting of one 32 bit register , three 16 bit registers , one
16 x 16 bit service memory , one 7 x 17 bit last-in first-out (LIFO ) memory , one adder circuit ,
decodifying logic , priority logic , error detection and management logic , one 16 bit multiplexer ,
one 8 bit counter and a timing network , contained in a housing the exterior dimensions ofwhich
do not exceed 23 x 82 mm, with not more than 64 connecting pins and bearing :
— the identification marking :
CSS 0484
or
— other identification markings relating to sequence control circuits complying with the
abovementioned description .
0
0
0
0
ex 85.21 D II Error correction and detection unit (ECDU) of bipolar technology , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
16 x 62 mm , with not more than 48 connecting pins and bearing :
— an identification marking either consisting of or including the following combinations of
figures and letters :
2960
74 F 630
74 F 631
DP 8400
74 LS 630
74 LS 631
or
— other identification markings relating to error correction and detection units (ECDUs )
complying with the abovementioned description
ex 85.21 D II Error detection and correction circuit of N-MOS ( including H-MOS ) technology capable of
detecting and correcting single bit errors and detecting all double bit errors , in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 25 x 25 mm , with not more than 68 contact areas and bearing:
No L 362 / 2520 . 12 . 86 Official Journal of the European Communities
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont 'd)
— an identification marking either consisting of or including the following combination of
figures :
8206
or
— other identification markings relating to N-MOS error detection and correction circuits
complying with the abovementioned description
ex 85.21 D II Burst error processor (BEP ) of N-MOS ( including H-MOS ) technology for detecting and
correcting multiple errors derived from a line of magnetic discs , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
16 X 54 mm , with not more than 40 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
Z 8065
AM 9520
AM 9521
or
— any other identification marking relating to N-MOS burst error processor complying with
the abovementioned description
ex 85.21 D II Electronic control circuit of bipolar technology in the form of a monolithic integrated circuit for
the control of dynamic random-access memories (D-RAMs), capable of multiplexing address
and generating timing , contained in a housing the exterior dimensions of which do not exceed
17 x 62 mm , with not more than 48 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
DP 8408
DP 8409
MB 1422
0
0
0
7
0
or
— other identification markings relating to electronic control circuits complying with the
abovementioned description
ex 85.21 D II N-MOS ( including H-MOS ) programmable communication interfaces (N-MOS PCIs ), in the
form of a monolithic integrated circuit , contained in a housing the exterior dimensions of which
do not exceed 17 x 39 mm , with not more than 28 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
8251 A
or
— other identification markings relating to N-MOS PCIs complying with the abovementioned
description
ex 85.21 D II Enhanced programmable communications interface (EPCI ), in the form of a monolithic
integrated circuit , contained in a housing the external dimensions of which do not exceed
17 x 39 mm , with not more than 28 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures :
2661
or
— other identification markings relating to EPCIs complying with the abovementioned
description
No L 362 / 26 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Serial interfaces , capable of implementing the data stream encoding , decoding and associated
control functions for a local area network , in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 16 x 33 mm, with not
more than 24 connecting pins and bearing :
— an identification marking either consisting of the following combination of figures or figures
and letters or one of those combinations :
AM 7991
8002
8023
82501
COM 9032
or
— other identification markings relating to serial interface devices complying with the
abovementioned description
ex 85.21 D II Station digital interface circuit for parallel / serial or serial / parallel conversion of digital signals
in telephone sets , of C-MOS technology (C-MOS STID), in the form of a monolithic integrated
circuit , contained in a housing the exterior dimensions of which do not exceed 17 x 39 mm,
with not more than 28 connecting pins , and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
WCC 295 G
or
— other identification markings referring to station interface digital circuits complying with
the abovementioned description
ex 85.21 D II N-MOS ( including H-MOS ) programmable interval timers (N-MOS PITs), in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 17 X 39 mm, with not more than 24 connecting pins and bearing:
— an identification marking either consisting of or including one of the following
combinations of figures :
0
0
0
0
8253 8254
or
— other identification markings relating to N-MOS PITs complying with the abovementioned
description
ex 85.21 D II Demodulator / tone decoder of bipolar technology for frequency decoding , in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 10 x 21 mm , with not more than 14 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
XR 2211
or
— other identification markings relating to demodulator tone decoders complying with the
abovementioned description
ex 85.21 D II C-MOS clock circuits , in the form of a monolithic integrated circuit , contained in a housing the
exterior dimensions of which do not exceed 16 x 54 mm, with more than 16 connecting pins ,
and bearing :
20 . 12 . 86 Official Journal of the European Communities No L 362 / 27
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
HI 2060
HI 2065
MSM 5537
T 3605
or
— other identification markings relating to clock circuits complying with the abovementioned
description
for the production of automatic time-switches , instrument panel clocks and clocks of a similar
type for motor vehicles ( a ) 0
ex 85.21 D II C-MOS clock circuits , operating from a single 1 ,5 V power supply , with a liquid crystal display
(LCD ) driver , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 15 x 21 mm, with not more than 56 connecting pins and
bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
TC 8219 AF
l or
— other identification markings relating to C-MOS clock circuits complying with the
abovementioned description 0
ex 85.21 D II Amplifier , in the form of a monolithic integrated analogue circuit , contained in a housing the
dimensions of which do not exceed 2 x 4 x 4 mm, with not more than 10 connecting pins and
bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
V 35
C 05
or
— other identification markings relating to amplifiers complying with the abovementioned
description
This amplifier is for the manufacture of products falling within subheading 90.19 B I ( a ) 0
ex 85.21 D II Transceivers with four channels (Quad bus ) of ALP Schottky technology with on-chip D type
registers and internal ODD 4 bit parity generator / checker , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
9 x 28 mm, with not more than 20 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
AM 2907
or
— other identification markings relating to transceivers (Quad bus ) complying with the
abovementioned description 0
ex 85.21 D II Four-line drivers of advanced , low-power Schottky technology , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
20 x 7 mm, with not more than 16 connecting pins and bearing:
— an identification marking consisting of or including one of the following combinations of
figures and letters :
AM 26LS29
AM 26LS31
SN 75172
SN 75174
(a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
No L 362 / 28 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
or
— other identification markings relating to four-line drivers of ALPS technology complying
with the abovementioned description
ex 85.21 D II Universal Synchronous /Asynchronous Receiver / Transmitter (USART ) of C-MOS
technology , in the form of a monolithic integrated circuit contained in a housing the exterior
dimensions of which do not exceed 17 x 39 mm , with not more than 32 connecting pins or
contact areas and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
MSM 82 C 51
or
— other identification markings relating to Universal Synchronous /Asynchronous
Receiver / Transmitters complying with the abovementioned descriipption
ex 85.21 D II 8 bit microprocessor of N-MOS ( including H-MOS ) technology with 16 bit internal
architecture , in the form of a monolithic integrated circuit consisting of a central processing unit
( CPU), a timing generator , two independent DMA channels , a programmable interrupt
controller , three programmable 16 bit timers , programmable memory and peripheral chip
select , a programmable wait state generator and a local bus controller , contained in a housing
the dimensions of which do not exceed 30 x 30 mm with not more than 68 connecting pins or
contact areas , and bearing :
— an identification marking consisting of or including the following combination of
figures :
80188
or
0
7
7
0
0
— other identification markings relating to microprocessors complying with the
abovementioned description
ex 85.21 D II 16 bit microprocessor of bipolar technology , in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 25 x 82 mm, with not
more than 68 connecting pins or contact areas and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
AM 29116 SBP 9989
or
— other identification markings relating to microprocessors complying with the
abovementioned description
ex 85.21 D II 16 bit microprocessor in N-MOS ( including H-MOS ) technology , in the form of a monolithic
integrated circuit , consisting of a central processing unit (CPU), a timing generator , two
independent DMA channels , a programmable interrupt controller , three programmable 16 bit
timers , programmable memory and external chip selection logic , a programmable wait state
generator with bus control unit , contained in a housing the exterior dimensions ofwhich do not
exceed 30 x 30 mm, with not more than 68 connecting pins or contact areas and bearing:
— an identification marking consisting of or including the following combination of
figures :
80186
or
— other identification markings relating to microprocessors complying with the
abovementioned description
20 . 12 . 86 Official Journal of the European Communities No L 362 / 29
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II 16-bit microprocessor of N-MOS technology ( including H-MOS ) in the form of a monolithic
integrated circuit , consisting of a central processing unit (CPU), a memory management and
protection unit (MMU) and a real address and virtual address operating mode system (OSO),
contained in the housing whose exterior dimensions do not exceed 30 x 30 mm , with not more
than 68 connecting pins or contact areas and bearing :
— an identification marking consisting of or including one of the following combinations :
80 286
or
— other identification markings relating to microprocessors complying with the
abovementioned description
ex 85.21 D II 32-bit microprocessor (MPU ) of C-MOS technology in the form of a monolithic integrated
circuit , contained in a housing whose exterior dimensions do not exceed 36 x 36 mm , with not
more than 114 connecting pins and bearing :
— an identification marking either consisting of or including the following combination :
MC 68020
or
— other identification markings relating to circuits complying with the abovementioned
description
ex 85.21 D II 32-bit microprocessor in C-MOS technology , in the form of a hybrid integrated circuit ,
consisting of a single substrate layer on which are mounted two chips , comprising a central
processing unit ( CPU ) and a memory unit , the exterior dimensions of which do not exceed
16 x 55 mm , with not more than 60 connecting pins and bearing :
10
0
0
0
— an identification marking consisting of or including the following combination of
figures :
57-00000 57-19400
or
— other identification markings for devices complying with the abovementioned
description
ex 85.21 D II Floating-point arithmetic co-processor (FPU ) of C-MOS technology , in the form of a
monolithic integrated circuit , consisting of eight 80-bit registers and a 32-bit data bus ,
contained in a housing whose exterior dimensions do not exceed 28 x 28 mm , with not more
than 80 connecting pins and bearing :
— an identification marking consisting of or including the following combination :
MC 68881
or
— other identification markings relating to circuits complying with the abovementioned
description
ex 85.21 D II Numeric processor extension unit of N-MOS ( including H-MOS ) technology (N-MOS NPX)
containing not more than 14 registers , in the form of a monolithic integrated circuit , contained
in a package the exterior dimensions of which do not exceed 15 x 52 mm, with not more than
40 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures or figures and letters :
No L 362 / 30 Official Journal of the European Communities 20 , 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
8087 TX 32081 W
80287
or
— other identification markings , relating to N-MOS NPXs complying with the
abovementioned description 0
ex 85.21 D II Floppy-disc data separator (FDDS), in the form of a monolithic integrated circuit , contained in
a housing the exterior dimensions of which do not exceed 27 x 8 mm, with not more than 20
connecting pins and bearing:
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
FDC 9216
FDC 921 6-B
WD 9216-00
WD 92 C 32
FDC 9229 T
FDC 9229 BT
or
— other identification markings relating to FDDS , complying with the abovementioned
description 0
ex 85.21 D II C-MOS-phoneme speech synthesizer , with a supply current of less than 10 mA, in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 17 x 39 mm, with not more than 28 connecting pins and bearing:
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
CM 54104 CM 54166 N2L CD 54123 N2L SSI 263
CM 54145 N2L CD 54121 N2L CD 54147 N2L
CM 54146 N2L CD 54122 N2L SC 01
or
— other identification markings relating to phoneme speech synthesizers complying with the
abovementioned description 0
ex 85.21 D II Triple video digital to analogue converter (VDAC), each channel having a capacity of not more
than 8 bits with a maximum conversion time of not more than 25 nanoseconds , in the form of a
hybrid or monolithic integrated circuit whether or not incorporating three random access
memories (RAMs) each with a storage capacity of not more than 2 K bits , contained in a
housing the exterior dimensions of which do not exceed 54 x 62 mm, with not more than 61
connecting pins and bearing:
— an identification marking consisting of one of the following combinations of letters and
figures :
VDAC 444 TD TDC 1334
RGB DAC 4 T HDAC 34010
RGB DAC 8 E HDAC 34020
RGB DAC 8 T
or
— other identification markings relating to triple VDACs complying with the abovementioned
description 0
ex 85.21 D II Electronically adjustable differential amplifiers for at least the full range of signals from 0 to not
less than 400 MHz in the form of a monolithic integrated circuit , contained in a housing the
exterior dimensions of which do not exceed 11x11 mm, with not more than 16 connecting
pins , and bearing:
20 . 12 . 86 Official Journal of the European Communities No L 362/ 31
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
— an identification marking consisting of or containing the following combination of
figures :
0078-10
or
— other identification markings relating to amplifiers complying with the abovementioned
description
ex 85.21 D II Static , random-access memories of bipolar technology (bipolar SRAMs), in the form of a
monolithic integrated circuit and with a storage capacity of 64 x 9 bits , contained in a housing
the exterior dimensions of which do not exceed 16 x 40 mm, with not more than
28 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
82 S 09 MBM 93419
or
— other identification markings relating to bipolar SRAMs complying with the
abovementioned description
ex 85.21 D II 8 bit ( octal ) dynamic memory bipolar driver in the form of a monolithic integrated circuit
contained in a housing the exterior dimensions of which do not exceed 16 X 33 mm, with not
more than 20 connecting pins and bearing :
— an identification marking consisting of or including one of the following combination of
figures and letters :
AM 2965
AM 2966
or
— other identification markings relating to dynamic memory bipolar drivers complying with
the above description
0
0
0
0
0
ex 85.21 D II Bus interface circuits of bipolar technology with 9 or 10 bit registers , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
9 x 34 mm, with not more than 24 connecting pins or contact areas and bearing :
— an identification marking consisting of or including one of the following combinations of
numbers and letters :
AM 29843
AM 29844
AM 29821
AM 29823
AM 29824
or
— other identification markings relating to BUS interface circuits which comply with the above
description
ex 85.21 D II Multiple bus interface circuit (Multiple Bus Buffer ) of low power Schottky technology for
interfacing the error correction and detection unit system data bus and dynamic random access
memory (D-RAM), in the form of a monolithic integrated circuit contained in a housing the
exterior dimensions ofwhich do not exceed 8x33 mm , with not more than 24 connecting pins
and bearing :
— an identification marking consisting of or including the following combination of numbers
and letters :
AM 2961
or
— other identification markings relating to error correction multiple bus buffers which comply
with the above description
No L 362 / 32 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty ( % )
ex 85.21 D II Status and shift control unit of bipolar technology in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 16 X 57 mm with not
more than 42 connecting pins , and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
AM 2904
or
— other identification markings relating to status and shift control units complying with the
above description
ex 85.21 D II Amplifier , in the form of a monolithic integrated analogue circuit the exterior dimensions of
which do not exceed 3x3 mm for use in the manufacture of products falling within
subheading 90.19 B I ( a )
ex 85.21 D II Text co-processor , in the form of a monolithic integrated circuit , contained in a housing the
exterior dimensions of which do not exceed 25 x 25 mm , with not more than 68 connecting
pins , and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
C 82730
or
— other identification markings relating to text co-processors complying with the above
description
ex 85.21 D II Single-chip-microcomputer , in the form of a monolithic integrated circuit , consisting of an
arithmetic-logic unit with a capacity of 8 bits plus an electronic , programmable , read-only
memory (EPROM) UV erasable with a capacity of 32 K bits and a random access memory
(RAM) with a capacity of 1 K bit , contained in a housing the exterior dimensions of which do
not exceed 15 x 50 mm, with a quartz window and not more than 40 connecting
pins and bearing :
0
0
0
0
0
— an identification marking either consisting of the following combination of figures or
including this combination :
8751 7742
or
— other identification markings relating to single-chip microcomputers which conform to the
foregoing description
ex 85.21 D II Single-chip microcomputers in C-MOS technology , in the form of a monolithic integrated
circuit consisting of an ALU with a capacity of 32 bits plus a ROM with a capacity of 24 K bits
and a RAM with a capacity of 2 K bits , contained in a housing the exterior dimensions ofwhich
are not less than 30 x 30 mm , with not less than 84 connecting pins or contact areas and
bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
MB 8764
or
— other identification markings relating to single-chip microcomputers complying with the
abovementioned description
ex 85.21 D II Subscriber line audio-processing circuit ( SLAC) with two digital signal processors , an
analogue-digital converter and a digital-analogue converter , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
17 x 39 mm with not more than 28 connecting pins and bearing :
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86 No L 362 / 33Official Journal of the European Communities
CCT
heading No Description
Rate of
autonomous
duty ( % )
ex 85.21 D II
(cont'd)
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
AM 7901
AM 7905
or
— other identification markings relating to SLACs complying with the abovementioned
description
ex 85.21 D II Non-volatile memory in the form of a monolithic integrated circuit , consisting of a C-MOS
S-RAM , with a capacity of 16 K bits and internal power supply , contained in a housing the
exterior dimensions of which do not exceed 19 x 36 mm , with not more than 28 connecting
pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
MK 48 Z 02 (B ) DS 1220 Y
or
— other identification markings relating to non-volatile memories complying with the
abovementioned description
ex 85.21 D II Input output circuit ofN-MOS ( including H-MOS ) technology for data control equipped with a
timing control with a static random access memory (S-RAM) with a capacity of 1 28 x 8 bits , in
the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 16 x 54 mm, with not more than 40 connecting pins and bearing:
— an identification marking either consisting of one of the following combinations of figures
or letters and figures or including one of those combinations :
6532
CO 10750
or
7
7
0
0
0
— other identification markings relating to input-output control circuits complying with the
abovementioned description
ex 85.21 D II Analogue-digital monolithic integrated circuit of bipolar technology , for damping the
oscillations of stepping motors during the positioning phase contained in a housing whose
exterior dimensions do not exceed 18 x 39 mm, with not more than 28 connecting pins and
bearing :
— an identification marking either consisting of or including the following combination of
letters :
STEDA
or
— other identification markings relating to integrated circuits complying with the
abovementioned description
ex 85.21 D II Analogue-digital monolithic integrated circuit used to control brushless motors , maintaining
them at a constant speed , contained in a housing the exterior dimensions ofwhich do not exceed
6 x 25 mm, with not more than 18 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
MGA 3015 A
or
— other identification markings relating to integrated circuits complying with the
abovementioned description
No L 362 / 34 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Analogue-digital monolithic integrated circuit of bipolar technology , capable of controlling
spindle motors and keeping their speed constant , contained in a housing whose exterior
dimensions do not exceed 9 x 25 mm, with not more than 20 connecting pins and
bearing:
— an identification marking either consisting of or including the following combinations of
figures and letters :
UC 1634 UC 1633 UC 3633 UC 3634
or
— other identification markings relating to analogue-digital integrated circuits complying with
the abovementioned description
ex 85.21 D II Memory management unit of N-MOS ( including H-MOS ) technology (N-MOS MMU) with a
maximum addressing capacity of 16 M bytes , in the form of a monolithic integrated circuit
contained in a housing the exterior dimensions, of which do not exceed 25 x 82 mm, with not
more than 64 connecting pins or 68 contact areas and bearing:
— an identification marking consisting of or including one of the following combinations of
figures and letters :
68451
TX 32082 W
or
— other identification markings relating to N-MOS MMUs complying with the
abovementioned description
ex 85.21 D II Memory controller of C-MOS technology , in the form of a monolithic integrated circuit ,
contained in a housing whose dimensions do not exceed 36 x 36 mm, with not more than 132
connecting pins and bearing :
0
0
0
0
— an identification marking either consisting of or including the following combination of
figures and letters :
MC 68851
or
— other identification markings relating to controllers complying with the abovementioned
description
ex 85.21 D II Electronic circuit of advanced low power Schottky (ALPS ) technology for the asynchronous
control of signal lines ( bus ) and the conversion of a local bus into a multiplexed bus (BAM) in
the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 37 x 13 mm , with not more than 28 connecting pins and bearing :
— the identification marking :
68452
or
— other identification markings relating to ALPS BAMs conforming to the foregoing
description
ex 85.21 D II Cathode-ray tube controller (CRTC ) of N-MOS ( including H-MOS ) technology in the form of
a monolithic integrated circuit contained in a housing the exterior dimensions of which do not
exceed 62 x 25 mm , with not more than 68 connecting pins and bearing:
— an identification marking either consisting of or including the following combination of
figures and letters :
20 . 12 . 86 Official Journal of the European Communities No L 362 / 35
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont 'd)
AM 8052
D 8275 H
P 8275 H
or
— other identification markings relating to CRTCs complying with the abovementioned
description
ex 85.21 D II Display controller and character generator (DCCG) for liquid crystal dot matrix display system
in the form of a monolithic integrated circuit of C-MOS technology contained in a housing the
exterior dimensions of which do not exceed 20 x 26 mm, with not more than 60 connecting
pins , and bearing:
— an identification marking consisting of the following combination of figures and letters :
HD 61830
or
— other identification markings relating to C-MOS Display Controller and character
generators complying with the abovementioned descriptions
ex 85.21 D II Video digital to analogue converter (VDAC) with a maximum conversion time of 10
nanoseconds , in the form of a hybrid integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 20 x 35 mm, with not more than 24 connecting pins and
bearing :
— an identification marking consisting of or including one of the following combination of
figures and letters :
VDAC 0405 H
VDAC 0605 H
VDAC 0805 H
or
— other identification markings relating to VDACs complying with the abovementioned
description
7
0
0
0
0
ex 85.21 D II Interpolation pulse generator of C-MOS technology for controlling geometrical functions , in
the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 17 x 39 mm, with not more than 28 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
KM 3701
or
— other identification markings relating to interpolation modules complying with the
abovementioned description
ex 85.21 D II Static , random access memory of C-MOS technology (C-MOS S-RAM) with a storage capacity
of 32 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 18 x 39 mm , with not more than 28 connecting pins and
bearing:
— an identification marking consisting of or including the following combination of figures
and letters :
TC 5532
or
— other identifying markings relating to C-MOS S-RAM complying with the abovementioned
description
No L 362 / 36 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Controller for servo-devices ofC-MOS technology in the form of a monolithic integrated circuit
contained in a housing the exterior dimensions of which do not exceed 17 x 54 mm, with not
more than 40 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
KM 3702
or
— other identification markings relating to controllers complying with the abovementioned
description
ex 85.21 D II Function generator of bipolar technology for the generation of variable waveforms , in the form
of a monolithic integrated circuit , contained in a housing the exterior dimensions of which do
not exceed 10 x 21 mm , with not more than 16 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
XR 2206
XR 8038
or
— other identification markings relating to function generators complying with the
abovementioned description
ex 85.21 D II Video amplifier of bipolar technology in the form of a monolithic integrated circuit , contained
in a housing the exterior dimensions of which do not exceed 17 x 17 mm, with not more than
44 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures :
0
0
0
0
702
703
or
— other identification markings relating to video amplifiers complying with the
abovementioned description
for use in the manufacture of portable colour television cameras ( a )
ex 85.21 D II Amplifier , of bipolar technology for the amplification of either read or write signals of floppy
discs , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 11 x 29 mm , with not more than 22 connecting pins and
bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
XR 2247
XR 3470
or
— other identification markings relating to amplifiers complying with the abovementioned
description
ex 85.21 D II Aperture and colour temperature balance controller of bipolar technology , in the form of a
monolithic integrated analogue circuit , contained in a housing the exterior dimensions ofwhich
do not exceed 17 x 17 mm, with not more than 44 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures :
704
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86 Official Journal of the European Communities No L 362 / 37
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
or
;— other identification markings relating to devices complying with the abovementioned
description
for use in the manufacture of portable colour television cameras ( a ) 0
ex 85.21 D II Impulse generator in C-MOS technology , in the form of a monolithic integrated digital circuit ,
contained in a housing the exterior dimensions of which do not exceed 25 X 25 mm , with not
more than 68 connecting pins and bearing :
— an identification marking consisting of or including one of the following combination of
figures :
705
706
or
— other identification markings relating to impulse generators complying with the
abovementioned description
for use in the manufacture of portable colour television cameras ( a ) 0
ex 85.21 D II Static random access memories of bipolar technology (bipolar S-RAMs) in the form of a
monolithic integrated circuit consisting of a substrate layer on which are mounted either 1 or 2
chips each having a storage capacity of 1 K bit , contained in a housing the exterior dimensions
of which do not exceed 13x13 mm, with not more than 23 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures :
770639
770823
5120360
7379769
or
— other identification markings relating to bipolar S-RAMs complying with the
abovementioned description 0
ex 85.21 D II Static memories consisting of two stacked substrate layers with one or two static random access
memories of bipolar technology (bipolar S-RAMs ) in the form ofmonolithic integrated circuits ,
each with a storage capacity of 1 K bits and with a maximum storage capacity of 4 K bits ,
contained in a housing the exterior dimensions of which do not exceed 13x13 mm, with not
more than 23 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures :
770965
4599497
7379442
ex 85.21 D II
or
— other identification markings relating to static memories complying with the
abovementioned description
Programmable digital signal synthesizer of C-MOS technology with 32 frequency generators to
generate eight notes each and a simultaneous output of up to 160 notes in the form of a
monolithic integrated circuit contained in a housing , the exterior dimensions of which do not
exceed 25 x 25 mm, with not more than 68 connecting pins or contact areas .
0
The housing bears :
— an identification marking either consisting of or including the following combination of
letters :
MEG
or
— other identification markings relating to digital synthesizers complying with the
abovementioned description 0
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
No L 362 / 38 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No
Description
Rate of
autonomous
duty (% )
ex 85.21 D II Repeater circuit , of bipolar technology for the regeneration of pulse code-modulated signals , in
the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 10 x 21 mm, with not more than 16 connecting pins and bearing:
— an identification marking consisting of or including the following combination of figures
and letters :
XR C 240
or
— other identification markings relating to repeater circuits complying with the
abovementioned description
ex 85.21 D II Dynamic random access memory controller of N-MOS ( including H-MOS ) technology
(N-MOS D-RAM controller ) capable of multiplexing addresses and generating timing , in the
form of a monolithic integrated circuit contained in a housing the exterior dimensions ofwhich
do not exceed 17 x 62 mm, with not more than 48 connecting pins or 52 contact areas , and
bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
C 8208
THCT 4502
or
— other identification markings relating to N-MOS D-RAM controllers complying with the
abovementioned description
ex 85.21 D II
0
0
0
0
Dual universal asynchronous receiver transmitter (DUART ) ofMOS technology , in the form of
a monolithic integrated circuit , contained in a housingwhose exterior dimensions do not exceed
15 x 52 mm, with not more than 40 connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations :
SCN 2681
MC 2681
or
— other identification markings relating to circuits complying with the abovementioned
description
ex 85.21 D II C-MOS clock / calendar circuit , incorporating a quartz crystal oscillator , independent timer
recorders and a timer , in the form of a monolithic integrated circuit , contained in a housing the
exterior dimensions ofwhich do not exceed 7x20 mm with not more than 1 6 connecting pins
and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
MM 58174 A 58274
or
— other identification markings relating to clock / calendar circuits complying with the
abovementioned description
ex 85.21 D II C-MOS clock circuit with audio and hour-count output , in the form of a monolithic integrated
circuit contained in a housing whose dimensions do not exceed 17 x 33 mm, with not more
than 24 connecting pins and bearing:
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
20 . 12 . 86 No L 362 / 39Official Journal of the European Communities
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
SVM 5530
7910
or
— other identification markings relating to clock circuits complying with the abovementioned
description 0
ex 85.21 D II Programmable asynchronous communication element circuit in N-MOS technology , for the
asynchronous transmission and reception of data , in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 16 x 54 mm, with not
more than 40 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
INS 8250 NS 16450
WD 8250 NS 16 C 450
or
— other identification markings relating to ACE circuits complying with the abovementioned
description 0
ex 85.21 D II Dynamic , random-access read /write memory of N-MOS ( including H-MOS ) technology ,
(N-MOS D-RAMs ) with a storage capacity of 64 K x 4 bits , in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
17x34 mm , with not more than 20 connecting pins arranged in two parallel lines (dual-in-line
package ) and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters
TMS 4464 PD 41254 PD 41464 TMM 41464
M5M 4464 HM 50464 MB 81464
or
— other identification markings relating to N-MOS D-RAMs . complying with the
abovementioned description 10
ex 85.21 D II Dynamic random access memories (DRAMs), of N-MOS ( including H-MOS ) technology with
a storage capacity of 256 K bits and access times not exceeding 150 ns , in the form of a
monolithic integrated circuit , contained in a housing the exterior dimensions of which do not
exceed 22 x 12 mm , with not more than 20 connecting pins with zig-zag in-line package and
bearing :
— an identification marking either consisting of or including one of the following combination
of figures and letters :
PD 41256 V
MB 81256 P
HM 56256 ZP
or
— other identification markings relating to components complying with the abovementioned
description 10
ex 85.21 D II Encoder / decoder circuit using Manchester code (MED) for the transmission of data in
continuous flux with a repeater mode in C-MOS technology , having an output voltage of 4,5
volts , in the form of a monolithic integrated circuit contained in a housing the exterior
dimensions of which do not exceed 16 x 33 mm , with not more than 20 connecting pins and
bearing :
— an identification marking consisting or including the following combination of figures and
letters :
HD 6409
No L 362 /40 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
orex 85.21 D II
(cont'd) — other identification markings relating to circuits complying with the abovementioned
description
ex 85.21 D II UV-erasable programmable read-only memories (EPROMs ) in the form of a monolithic
integrated circuit with a storage capacity of 512 K bits , contained in a housing the exterior
dimensions of which do not exceed 20 x 42 mm , with a quartz window on the upper surface .
The housing bears :
— an identification marking consisting or including the following combination of figures and
letters :
AM 27512 MBM 27 C 512
or
— other identification markings relating to EPROMs complying with the abovementioned
description
ex 85.21 D II TTL logic modules in bipolar technology with not more than six logic functions in the form of a
monolithic integrated circuit contained in a housing the exterior dimensions of which do not
exceed 17 x 34 mm, with not more than 24 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures or letters :
SH 767 369
SH 998 088
or
— another identification marking relating to logic modules as described above
0
0
0
0
7
ex 85.21 D II Control and interface circuit for central processor (CPU-controller ) of C-MOS technology in
the form of a monolithic integrated circuit contained in a housing the exterior dimensions of
which do not exceed 25 x 25 mm, with not more than 68 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
letters and figures :
FE 2000
L1A0392
or
— other identification markings relating to control and interfacing circuits complying with the
abovementioned description
ex 85.21 D II Circuit for the control of floppy discs ( floppy disc controller ) of C-MOS technology , in the form
of a monolithic integrated circuit contained in a housing the exterior dimensions of which do
not exceed 16 x 62 mm , with not more than 48 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
letters and figures :
L 1 A 0519
G 70360-33
MB 89311
or
— other identification markings relating to adaptor circuits complying with the
abovementioned description
ex 85.21 D II Pulse code modulation (PCM) codec and filter ofNMOS ( including H-MOS ) technology , in the
form of a monolithic integrated circuit , consisting of a fully integrated PCM codec with
transmit / receive filters , contained in a housing the exterior dimensions ofwhich do not exceed
10 x 23 mm , with not more than 16 connecting pins and bearing :
20 . 12 . 86 Official Journal of the European Communities No L 362 / 41
CCT
heading No Description
Rate of
autonomous
duty ( % )
ex 85.21 D II
(cont'd)
— an identification marking either consisting of or including one of the following
combinations of figures :
2916
2917
or
— either identification markings relating to PCM codec and filter devices complying with the
abovementioned description
ex 85.21 D II 6-Channel monolithic integrated circuit (Read /write data processor circuit ) for the
amplification and conversion of read signals and conversion ofwrite signals for hard disc drives ,
contained in a housing the exterior dimensions of which do not exceed 19x38 mm , with not
more than 28 connecting pins or contact areas and bearing :
— an identification marking consisting of or including the following combination of letters and
figures :
SSI 540 SSI 541
or
— other identification markings relating to integrated circuits complying with the
abovementioned description
ex 85.21 D II 8-Channel control circuit for maintaining a constant electromagnetic traction force with
incorporated diodes and a storage capacity of 8 bits , in the form of a monolithic integrated
circuit , of C-MOS technology contained in a housing the exterior dimensions of which do not
exceed 9 x 28 mm , with not more than 22 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
UCN 5801
or
7
0
0
0
0
— other identification markings relating to control circuits complying with the
abovementioned description
ex 85.21 D II 4-Channel control circuit for maintaining a constant electro magnetic traction force with
incorporated diodes and a storage capacity of 4 bits , in the form of a monolithic integrated
circuit of C-MOS technology , contained in a housing the exterior dimensions of which do not
exceed 7 x 22 mm , with not more than 16 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
UCN 5813
or
— other identification markings relating to control circuits complying with the
abovementioned description
ex 85.21 D II Six-channel monolithic integrated circuit for the generation of read /write signals for hard disc
drives , contained in a housing the exterior dimensions of which do not exceed 13 x 13 mm ,
with not more than 28 connecting pins and bearing :
— an identification marking consisting of or including the following combination of letters and
figures :
SSI 117
or
— other identification markings relating to integrated circuits complying with the
abovementioned description
No L 362 /42 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Programmable non-erasable read-only memories (PROMS) with a storage capacity of 16 K
bits , in the form of a monolithic integrated circuit contained in a housing the exterior
dimensions of which do not exceed 39 x 17 mm, with not more than 32 connecting pins or
contact areas and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
27 PS 191 A
29683 :
MB 7137
MB 7138
7 C 245
7 C 291
7 C 292
HM 6616
MB 71 33
MB 7134
MB 7151
MB 7152
or
— other identification markings relating to PROMS complying with the abovementioned
description
ex 85.21 D II Amplifiers for a full range of signals from 0 to 60 KHz in the form of a monolithic integrated
circuit contained in a housing the exterior dimensions of which do not exceed 6 x 13 x 26
mm , with not more than 18 connecting pins and a leakage of not more than 0,3nA and
bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
ISO 100
or
— other identification markings relating to amplifiers complying with the abovementioned
description , for use in the manufacture of telephone exchanges ( a )
ex 85.21 D II Single chip microcomputer of C-MOS technology , in the form of a monolithic integrated
circuit , consisting of an arithmetical logic unit (ALU ) with an organization of 4 bits , a read-only
memory (ROM ) with a storage capacity of 2 K x 8 bits , a dual-tone , multi-frequency (DTMF)
generator , a random access memory ( RAM) with a storage capacity of 1 K bit , whether or not
with another random access memory (RAM) with a storage capacity of 512 bits , contained in a
housing whose exterior dimensions do not exceed 16 x 54 mm, with not more than
42 connecting pins and bearing :
0
0
0
0
— an identification marking consisting of one of the following combination of figures and
letters :
T 6978 TCM 8301 TCM 8302
or
— other identification markings relating to single chip microcomputers complying with the
abovementioned description
ex 85.21 D II Static random access memories of C-MOS technology (C-MOS S-RAMs) in the form of a
monolithic integrated circuit with a storage capacity of 16 x 4 bits , an access time not
exceeding 35 ns , contained in a housing the exterior dimensions of which do not exceed
9 x 21 mm, with not more than 16 connecting pins and bearing :
— an identification marking either consisting of or containing one of the following
combinations of figures and letters :
CY7C189
CY7C190
CY74S189
CY54S189
CY27S03
CY27S07
or
— other identification markings relating to C-MOS S-RAMs complying with the
abovementioned description
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
20 . 12 . 86 Official Journal of the European Communities No L 362 / 43
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Static random access memories of C-MOS technology (C-MOS S-RAMs ) in the form of a
monolithic integrated circuit with a storage capacity of 256 x 4 bits and an access time not
exceeding 60 ns , contained in a housing the exterior dimensions of which do not exceed
12 x 29 mm , with not more than 22 connecting pins and bearing:
— an identification marking either consisting of or including one of the following
combinations of figures or figures and letters :
CY7C122
CY93422 / 93L422
or
— other identification markings relating to C-MOS S-RAMs complying with the
abovementioned description
ex 85.21 D II Electrically erasable , programmable read-only memories ( so-called E2 PROMs), in the form of
an unmounted monolithic integrated circuit ( chip ) with a storage capacity of 16 K bits , used in
the manufacture of microwave systems for the identification of persons and objects ( a )
ex 85.21 D II Dynamic read /write random access memories manufactured in N-MOS ( including H-MOS )
technology (D-RAMs), in the form of a monolithic integrated circuit , consisting of a substrate
layer with not less than two and not more than eight chips having a storage capacity of 128 , 192
or 256 K bits and a storage capacity of not less than 256 K bits and not more than two megabits ,
contained in a housing whose dimensions do not exceed 30 x 30 mm , with not more than 57
connecting pins and bearing :
— an identification marking either consisting of or including one of the following
combinations of figures :
6031587
6031591
6025841
6025843
6025856
6025858
6870392 *
6870393
6870395
7379172
7379174
7379176
7379181
0
0
0
0
or
— other identification markings relating to dynamic read /write memories of the type
described above
ex 85.21 D II Dual port dynamic random access memory (D-RAM) of N-MOS ( including H-MOS )
technology , with data registers and a serial read output control , with a storage capacity of
256 K bits in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 13 x 39 mm, with not more than 24 connecting pins and
bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
MB 81461
PD 41264
or
— other identification markings relating to D-RAMs complying with the abovementioned
description
ex 85.21 D II Bus interface circuit in C-MOS technology , in the form of a monolithic integrated circuit , for the
control of communication lines comprising a numerical bus , two independent receivers and a
transmitter consisting of a first-in first-out ( FIFO ) memory contained in a housing whose
exterior dimensions do not exceed 20 x 52 mm with not more than 44 connecting pins or
contact areas and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
HS 3282
( a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .
No L 362 /44 Official Journal of the European Communities 20 . 12. 86
CCT
heading No Description
Rate of
autonomous
duty ( % )
orex 85.21 D II
(cont'd) — other identification markings relating to bus interface circuits and corresponding to the
abovementioned description
ex 85.21 D II Monolithic integrated circuit in N-MOS technology ( including H-MOS ) for the display of
graphic symbols on a cathode-ray tube operating in stroke mode , contained in a housing whose
exterior dimensions do not exceed 28 x 61 mm, with not more than 68 connecting pins and
bearing :
— an identification marking consisting of or including the following combinations of figures
and letters :
FCD 28 042 277 , 96 114 899 , 96 149 135 , 96 114 898
or
— other identification markings relating to circuits corresponding to the abovementioned
description
ex 85.21 D II Static , random access memories (S-RAMs) of C-MOS technology , with a storage capacity of
256 K bits , in the form of a monolithic integrated circuit , contained in a housing the exterior
dimensions of which do not exceed 39 x 17 mm, with not more than 28 connecting pins and
bearing :
— an identification marking either consisting of or including one of the following
combinations of figures and letters :
HM 62256
PD 43256 C
TC 55257 P
or
— other identification markings relating to S-RAMs complying with the abovementioned
description
0
0
0
0
0
ex 85.21 D II Random access memories of ECL technology (ECL-RAMs) with a storage capacity of
256 x 4 bits , and access time not exceeding 8 ns in the form of a monolithic integrated circuit ,
contained in a housing the dimensions ofwhich do not exceed 11 x 32 mm , with not more than
24 connecting pins and bearing:
— an identification marking either consisting of or including, the following combination of
figures :
10422
10422 A
or
— other identification markings relating to ECL-RAMs complying with the abovementioned
description
ex 85.21 D II Random access memories of ECL technology (ECL-RAMs ) with a storage capacity of 16 K bits
and an access time not exceeding 15 ns in the form of a monolithic integrated circuit , contained
in a housing the dimensions of which do not exceed 9 X 27 mm, with not more than 20
connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures :
10480
or
— other identification markings relating to ECL-RAMs complying with the abovementioned
description
ex 85.21 D II Octal line driver of Schottky-TTL technology in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 14x14 mm, with not
more than 28 connecting pins or contact areas and bearing :
20 , 12 . 86 Official Journal of the European Communities No L 362 / 45
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
— an identification marking either consisting of or including the following combination of
figures and letters :
5170 NE 5170 UC 5170
or
— other identification markings relating to octal line drivers complying with the
abovementioned description
ex 85.21 D II Octal line receiver of Schottky-TTL technology in the form of a monolithic integrated circuit ,
contained in a housing the exterior dimensions of which do not exceed 14 x 14 mm, with not
more than 28 connecting pins or contact areas and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
5180 NE 5180
5181 NE 5181
8510 8511
or
— other identification markings relating to octal line receivers complying with the
abovementioned description
ex 85.21 D II Interface circuit for the synchronization of data flow from a hard disk drive , in the form
of a monolithic integrated circuit , contained in a housing whose dimensions do not exceed
16 x 35 mm, with not more than 28 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
0
0
0
0
DP 8462
or
— other identification markings relating to interfaces complying with the abovementioned
description
ex 85.21 D II Hard Disc Data Separator (HDDS ) in the form of a monolithic integrated circuit , contained
in a housing whose exterior dimensions do not exceed 16 x 37 mm , with not more than
28 connecting pins and bearing:
— an identification marking consisting of or including one of the following combinations of
figures and letters :
DP 8465
DP 8460-2
DP 8460-3
DP 8460-4
WD 10C20
HDC 9226
or
— other identification markings relating to devices complying with the abovementioned
description
ex 85.21 D II Hybrid integrated circuit for electromagnet control consisting of four Darlington pairs
(one Darlington = two transistors with a cascade connection ) contained in a housing having
exterior dimensions which do not exceed 12 x 27 mm with not more than 10 connecting pins
and bearing:
— an identification marking consisting of or including the following combination of figures
and letters :
TH 3L10 TH 3L20 PU 4419
No L 362 /46 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty ( % )
orex 85.21 D II
(cont'd) — other identification markings relating to integrated circuits complying with the
abovementioned description
ex 85.21 D II Interface circuit of C-MOS technology for signals between peripheral hard disc memory units
and central units in the form of a monolithic integrated circuit contained in a housing whose
exterior dimensions do not exceed 28 X 53 mm with not more than 68 connecting pins or
contact areas and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
AIC 500
AIC 16000
OMTI 508
OMTI 509
WD 11 COO
or
— other identification markings relating to interface circuits complying with the
abovementioned description
ex 85.21 D II Sequential data control circuit of MOS technology for interface between a hard disc memory
unit and the memory control unit in the form of a monolithic integrated circuit of MOS
technology contained in a housing whose exterior dimensions do not exceed 28 x 54 mm , with
not more than 68 connecting pins and bearing :
— an identification marking consisting of or including one of the following combinations of
figures and letters :
AIC 010
AIC 100
OMTI 505
or
0
0
0
0
0
— other identification markings relating to sequential circuits complying with the
abovementioned description
ex 85.21 D II Encoder / decoder serial interface circuit for hard disc drives , in the form of a monolithic
integrated circuit contained in a housing whose exterior dimensions do not exceed 17 X 37 mm
with not more than 28 connecting pins or contact areas and bearing:
— an identification marking consisting of or including one of the following combinations of
figures and letters :
OMTI 507
OMTI 5027
AIC 250
AIC 270
or
— other identification markings relating to interface circuits complying with the
abovementioned description
ex 85.21 D II 4-channel read /write monolithic integrated circuit of bipolar technology for controlling
magnetic heads in hard disk units , contained in a housing whose exterior dimensions do not
exceed 12 x 19 mm, with not more than 28 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
SSI 510
or
— other identification markings relating to integrated circuits complying with the
abovementioned description
20 . 12 . 86 Official Journal of the European Communities No L 362 / 47
CCT
heading No Description
Rate of
autonomous
duty ( % )
ex 85.21 D II Electronic control circuit for static memory control ( S / RAM) with address multiplexing and
pulse generation facility , in the form of a monolithic integrated circuit of MOS technology
contained in a housing whose dimensions do not exceed 28 x 54 mm , with not more than
68 connecting pins or contact areas and bearing :
— an identification marking consisting of or including one of the following combination of
figures and letters :
OMTI 506
AIC 300
or
— other identification markings relating to electronic control circuits complying with the
abovementioned description
ex 85.21 D II Semi-custom logic arrays (gate arrays ) of C-MOS technology with metal gates , in the form of a
monolithic integrated circuit with an operating voltage of 12 volts , with not less than 637
2-input functions , having within the array a digital code produced by an electron beam ,
contained in a housing whose exterior dimensions do not exceed 29 x 1 1 mm , with not more
than 22 connecting pins and bearing :
— an identification marking either consisting of or including one of the following combination
of figures and letters :
FB 215
or
— other identification markings relating to gate arrays complying with the abovementioned
description
ex 85.21 D II Pulse code modulation (PCM) codec ofN-MOS ( including H-MOS ) technology , in the form of
a monolithic integrated circuit , consisting of a sample and hold circuit digital to analogue
converter , comparator , successive approximation register and logic function to interface to a
full duplex PCM link , contained in a housing whose exterior dimensions do not exceed 11x28
mm, with not more than 22 connecting pins and bearing :
0
7
7
7
— an identification marking consisting of or including the following combination of figures
and letters :
2911 A-l
or
— other identification markings relating to PCM codecs complying with the abovementioned
description
ex 85.21 D II Pulse code modulation (PCM) transmit / receive filter of N-MOS ( including H-MOS)
technology , in the form of a monolithic integrated circuit , consisting of two filters of a PCM
line or trunk termination , contained in a housing whose exterior dimensions do not exceed
10 x 21 mm , with not more than 16 connecting pins and bearing:
— an identification marking consisting of or including the following combination of figures
and letters :
D 2912 A
or
— other identification markings relating to PCM filters complying with the abovementioned
description
ex 85.21 D II Dynamic random access memories of C-MOS technology (C-MOS D-RAMs ) with a storage
capacity of 256 K bits in the form of a monolithic integrated circuit , contained in a housing
whose external dimensions do not exceed 17 x 34 mm , with not more than 1 8 connecting pins
and bearing :
No L 362 / 48 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II
(cont'd)
— an identification marking consisting of or including the following combination of figures
and letters :
P 51 C 256
P 51 C 259
or
— other identification markings relating to C-MOS D-RAMs complying with the
abovementioned description
ex 85.21 D II Analogue / digital signal converter , containing amplifiers , D /A and A/D converters with a
supply voltage of 12 volts ± 10% and a digital serial interface with asynchronous
receiver / transmitter , in the form of a monolithic integrated circuit , contained in a housing
whose external dimensions do not exceed 18x18 mm, with not more than 44 connecting pins
or contact areas and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
AD 75002
or
— other identification markings relating to programmable amplifiers with asynchronous
receiver / transmitter complying with the abovementioned description
ex 85.21 D II Cathode ray tube controller (CRTC ) of bipolar technology in the form of a monolithic
integrated circuit contained in a housing whose exterior dimensions do not exceed 15x55 mm
with not more than 40 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
SCB 2675
or
0
0
0
0
0
— other identification markings relating to CRTCs complying with the abovementioned
description
ex 85.21 D II Monochrome display controller (MDC) of C-MOS technology , in the form of a monolithic
integrated circuit , contained in a housing whose exterior dimensions do not exceed 25 x 25
mm, with not more than 68 connecting pins and bearing:
— an identification marking either consisting of or including the following combination :
01-01.00 551 A
or
— other identification markings relating to circuits complying with the abovementioned
description
ex 85.21 D II Programmable non-erasable read-only memories (PROMs) with a storage capacity of 32 K bits ,
in the form of a monolithic integrated circuit , whose external dimensions do not exceed
17 x 39 mm , with not more than 32 connecting pins or contact areas and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
63S3281 AM 27S43 MB 7141 MB 7142
or
— other identification markings relating to PROMs complying with the abovementioned
description
20 . 12 . 86 Official Journal of the European Communities No L 362 /49
CGT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Programmable advanced video display controllers (AVDCs) of N-MOS ( including H-MOS )
technology in the form of a monolithic integrated circuit , contained in a housing whose external
dimensions do not exceed 15 x 55 mm, with not more than 40 connecting pins and
bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
SCN 2674
or
— other identification markings relating to controllers complying with the abovementioned
description
ex 85.21 D II Control circuit of TTL-technology in the form of a monolithic integrated circuit for the firing of
magnetic print hammers , contained in a housing the exterior dimensions ofwhich do not exceed
7 X 20 mm with not more than 16 connecting pins and bearing :
— an identification marking consisting of or including the following combination of
figures :
801379-002
or
— other identification markings relating to integrated circuits complying with the
abovementioned description
ex 85.21 D II Subscriber-connection units ( crosspoint switches ) with not less than four and not more than 12
switches and an operating voltage of at least 150 V, in the form of a hybrid integrated circuit ,
contained in a housing whose dimensions do not exceed 92 x 41 mm , with not more than 94
connecting pins and bearing:
— an identification marking consisting of or including the following combinations :
904
719
or
7
0
0
0
0
— other identification markings relating to a crosspoint switch complying with the
abovementioned description
ex 85.21 D II 8 x 8 bit multiplier accumulator (MAC) of C-MOS technology in the form of a monolithic
integrated circuit , contained in a housing the exterior dimensions of which do not exceed
62 x 16 mm, with not more than 48 connecting pins and bearing:
— an identification marking either consisting of or including the following combination of
numbers and letters :
ADSP-1008A
or
— other identification markings relating to MACs complying with the abovementioned
description
ex 85.21 D II Analogue to digital converter for the calculation of the average value of variable wave-forms , in
the form of a monolithic integrated circuit , contained in a housing the exterior dimensions of
which do not exceed 18 x 10 mm, with not more than 14 connecting pins and bearing :
— an identification marking consisting of or including the following combination of numbers
and letters :
AD 536 A
or
— other identification markings relating to converters complying with the abovementioned
description
No L 362 / 50 Official Journal of the European Communities 20 . 12 . 86
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II 1 2-bit analogue-to-digital converter in the form of a monolithic integrated circuit incorporating
a voltage reference and clock , contained in a housing the external dimensions of which do not
exceed 36 x 15 mm, with not more than 28 connecting pins and bearing :
— an identification marking either consisting of or including the following combination of
figures and letters :
AD574A
or
— other identification markings for devices relating to the above description 0
ex 85.21 D II 4-channel digital-to-analogue converter , each channel having a capacity of 12 bits , in the form
of a hybrid integrated circuit contained in a housing the external dimensions of which do not
exceed 41 x 21 mm with not more than 28 connecting pins and bearing :
— an identification marking consisting of or including the following combination of numbers
and letters :
AD390
or
— other identification markings relating to microprocessors complying with the
abovementioned description 0
ex 85.21 D II Buffer management control processor in N-MOS ( including H-MOS) technology in the form of
a monolithic integrated circuit contained in a housing whose exterior dimensions do not exceed
54 x 17 mm with not more than 40 connecting pins and bearing :
— an identification marking consisting of or including the following combination of figures
and letters :
WD 1015
or
— other identification markings relating to buffer management control processors complying
with the abovementioned description 0
ex 85.21 D II Buffer manager and controler of C-MOS technology in the form of a monolithic integrated
circuit contained in a housing whose exterior dimensions do not exceed 31 mm by 31 mm with
not more than 84 connecting pins or contact areas and bearing :
— an identification marking consisting of or including the following combination :
WD11C00-22
or
— other identification markings for devices relating to the abovementioned description 0
ex 85.21 D II Thermocouple amplifier for instrumentation control at temperatures from 0 ° to 50 °C ,
incorporating an alarm system , in the form of a monolithic integrated circuit contained in a
housing the external dimensions of which do not exceed 20 x 8 mm with not more than 14
connecting pins and bearing:
— an identification marking either consisting of or including the following combination of
figures and letters :
AD594
AD595
or
— other identification markings relating to thermocouple amplifiers complying with the
abovementioned description 0
20 . 12 . 86 Official Journal of the European Communities No L 362 / 51
CCT
heading No Description
Rate of
autonomous
duty (% )
ex 85.21 D II Temperature transducer in the form of a monolithic analogue integrated circuit contained in a
housing the exterior dimensions of which do not exceed 6x4 mm with not more than three
connecting pins and bearing:
— an identification marking consisting of or including the following combination of numbers
and letters :
AD 590
or
— other identification markings relating to transducers complying with the abovementioned
description 0
ex 85.21 E Deflector yoke for cathode ray tubes with an operating frequency of between 31 250 Hz and
64 000 Hz incorporating a quadripolar magnet 0
ex 85.23 B Insulated winding wire of aluminium of a purity of not less than 99,5 % by weight , neither
lacquered , varnished nor enamelled , with a total thickness of not less than 0,15 mm and not
more than 0,16 mm 0
ex 90.02 B Image reversers made up from an assembly of optical fibres 0
ex 90.02 B Adjustable lens unit , having a focal length of between 115 mm and 140 mm, a diameter of not
less than 120 mm and not more than 130 mm, and comprising a combination of between four
and eight glass or methacrylic lenses , each lens coated on at least one side with a magnesium
fluoride layer , for use in the manufacture of video projectors ( a ) 0
ex 90.02 B Element , consisting of two rows of rigid optical filaments mounted between two plastic plates ,
whose maximum external dimensions do not exceed 276 x 20 x 5 mm, not fitted with cables
or connectors , for use in the manufacture of photocopiers ( a ) 0
ex 90.10 A Optical unit for photocopiers consisting of two rows of rigid optical monofilament fibres
between two plates of plastic material , a tube lamp and a metal reflector , mounted on a metal
structure whose maximum dimensions do not exceed 335 x 100 x 40 mm 0
ex 90.10 A Unit for photocopier , not fitted with an optical fibre assembly , consisting of a halogen lamp and
metal reflector mounted in a metal structure whose maximum dimensions (without taking
account of cables and connectors ) do not exceed 290 X 112 X 53 mm 0
ex 90.19 B II Portable reading appliance for the visually handicapped in which a fibre optic camera transmits
a magnified image on to a display screen , and parts thereof 3
ex 92.12 A Rigid magnetic disks , prelubricated , oxide type , with a high coercivity ( 800 Oe), an outer
diameter of 95 mm, an inner diameter of 25 mm and a thickness of 1,27 mm 0
(a ) Control of the use for this special purpose shall be carried out pursuant to the relevant Community provisions .


Full & Egal Universal Law Academy